PVC6A501C01B00 Murata Electronics North America, PVC6A501C01B00 Datasheet - Page 49
![TRIM POT 500OHM 1 TURN TOP ADJ](/photos/8/54/85467/pvc6a_series_sml.jpg)
PVC6A501C01B00
Manufacturer Part Number
PVC6A501C01B00
Description
TRIM POT 500OHM 1 TURN TOP ADJ
Manufacturer
Murata Electronics North America
Series
PVC6r
Datasheet
1.PVZ3A503A01R00.pdf
(55 pages)
Specifications of PVC6A501C01B00
Resistance (ohms)
500
Power (watts)
0.5W, 1/2W
Taper
Linear
Tolerance
±10%
Temperature Coefficient
±100ppm/°C
Number Of Turns
Single
Adjustment Type
Top Adjustment
Mounting Type
Through Hole
Resistive Material
Ceramic
Package / Case
Square - 0.272" L x 0.272" W x 0.205" H (6.90mm x 6.90mm x 5.20mm)
Resistance In Ohms
500
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
490-2710
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
No.
10 Temperature Road Life
11 High Temperature Exposure
12
13
6
7
8
9
SMD Sealed Type (PVG3/M4A_D01/G5)/Lead Sealed Type (PV32/12/37/36) Specifications and Test Methods
Continued from the preceding page.
Temperature Cycle
Humidity
Vibration
Shock
Low Temperature Exposure
(Except for PVM4A---D01)
Low Temperature Operation
(Only for PVM4A---D01)
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Item
The trimmer potentiometer should be subjected to Table 4 temperature for 5 cycles. The trimmer potentiometer
should be removed from the chamber, and maintained at a temperature of 25 5 C for 1-2 hours.
1) PV12, PV32, PVM4A---D01 series
The trimmer potentiometer should be placed in a chamber at a temperature of 40 2 C and a humidity of 90-95%
without loading for 250 8 hours (500 12 hours for PVM4A---D01 series). The trimmer potentiometer should be
removed from the chamber, and maintained at a temperature of 25 5 C for 5 1/6 hours.
2) PVG3, PVG5, PV36, PV37 series
The trimmer potentiometer should be subjected to the programmed humidity environment for 10cycle (see Figure 3).
The trimmer potentiometer should be removed from the chamber, and maintained at a temperature of 25 5 C for
1.5 1/2 hours.
1) PV-- series
The trimmer potentiometer should be vibrated throughout the frequency range at the 20G level. A complete frequen-
cy range, 10Hz to 2000Hz and back, should be made within 15 minutes for a total of 4 sweeps in each of the three
axis directions for a total of 12 sweeps.
1) PV-- series
The trimmer potentiometer should be shocked at the 100G level and should be subjected to 4 shocks in each of the
three axis directions for a total of 12 shocks.
2) PVM4A---D01 series
The trimmer potentiometer should be shocked at the 100G level and should be subjected to 3 shocks in each of the
six axis directions for a total of 18 shocks.
Full rated continuous working voltage not exceeding the maximum rated voltage should be applied intermittently
between terminal #1 and terminal #3 of the trimmer potentiometer, 1.5 hours on and 0.5 hours off, for a total of
1000 12 hours, at a temperature of 70 2 C (85 2 C for PV37 series). The trimmer potentiometer should be
removed from the chamber, and maintained at a temperature of 25 5 C for 1 to 2 hours.
The trimmer potentiometer should be placed in a chamber at a temperature of 125 3 C 250 8 hours without load-
ing. The trimmer potentiometer should be removed from the chamber, and maintained at a temperature of 25 5 C
for 1 to 2 hours.
The trimmer potentiometer should be placed in a chamber at a temperature of -55 3 C for 1 hours without loading.
Full rated continuous working voltage not exceeding the maximum rated voltage should be applied for 45 minutes.
The trimmer potentiometer should be removed from the chamber, and maintained at a temperature of 25 5 C for
approximately 24 hours.
The trimmer potentiometer should be placed in a chamber at a temperature of -25 3 C (-55 3 C for PVM4A---
D01 series) 48 4 hours without loading. The trimmer potentiometer should be removed from the chamber, and main-
tained at a temperature of 25 5 C for 1-2 hours.
Temp. ( C)
-10
Time (min.)
70
65
60
55
50
45
40
35
30
25
20
15
10
-5
Sequence
5
0
Table 4: One cycle of temperature cycle.
INITIAL CONDITIONING
IN A DRY OVEN
HUMIDITY
UNCONTROLLED
INITIAL MEASUREMENTS
AS SPECIFIED IN 3.2
UNLESS OTHERWISE SPECIFIED
TEMPERATURE TOLERANCE IS,
CHAMBER EXCEPT THE IMMEDIATE
VICINITY OF THE SPECIMENS AND
THE CHAMBER SURFACES
2 C AT ALL POINTS WITHIN THE
PV-- series
PRIOR TO FIRST CYCLE
UNLESS OTHERWISE
SPECIFIED
24 HOURS
-55 3
30
1
0
STEP 1
1
90-98%RH
RATE OF CHANGE OF TEMPERATURE IS UNSPECIFIED.
HOWEVER, SPECIMENS SHOULD NOT BE SUBJECTED
TO RADIANT HEAT FROM CHAMBER-CONDITIONING
PROCESSES
5 max.
+25 2
2
VOLTAGE APPLIED AS SPECIFIED IN 3.5
2
3
STEP 2
CIRCULATION OF CONDITIONING AIR SHOULD
BE AT A MINIMUM CUBIC RATE PER MINUTE
EQUIVALENT TO 5 TIMES THE VOLUME OF
THE CHAMBER
4
+125 3
5
STEPS 7a AND 7b PERFORMED DURING ANY
5 OF THE FIRST 9 CYCLES. HUMIDITY
UNCONTROLLED DURING STEPS 7a AND 7b
ONLY
ONE CYCLE 24 HOURS. REPEAT AS SPECIFIED IN 3.3
80-98%RH
30
STEP 3
6
Figure 3
3
7
Test Methods
8
5 max.
STEP 4
+25 2
+10 C
9
-2 C
4
90-98%RH
10
11
STEP 5
12
13
80-98%RH
14
STEP 6
15
16
17
MIL-STD-202 METHOD 106
18
END OF FINAL CYCLE
MEASUREMENTS AS
SPECIFIED IN 3.6
STEP 7a
90-98%RH
19
STEP 7
Continued on the following page.
20
21
22 23 24
STEP 7b
R50E.pdf
47
11.1.17
7