M165-TG-24D Omron, M165-TG-24D Datasheet - Page 21

• Manufacturer Part Number: M165-TG-24D
• Description: PILOT LIGHT ROUND GREEN
• Manufacturer: Omron
• Series: M16r
• Type: LEDr

Specifications of M165-TG-24D

• Lens Color: Green
• Panel Cutout Dimensions: 16mm (Round)
• Voltage: 24V
• Shape: Round
• Illumination: Not Illuminated
• Contact Rating: 10 mAmps
• Features: Terminal layout simplifies common wiring
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: Use non-corrosive resin fluid as the flux
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: M165TG24D; Z1359

Precautions
J CORRECT USE
Mounting
Always make sure that the power is turned OFF before mounting,
removing, or wiring the Switch, or performing maintenance.
Do not tighten the mounting nut more than necessary using tools
such as pointed-nose pliers. Doing so will damage the mounting
nut. The tightening torque is 0.20 to 0.39 N • m (3 to 5 kgf • cm).
Wiring
Solder terminals and quick-connect terminals (#110) are
commonly used for terminals.
Be sure to use electrical wires that are a size appropriate for the
applied voltage and carry current (conductor size is 0.5 to 0.75
mm
below. If the soldering is not properly performed, the lead wires
will become detached, resulting in short-circuits.
1. Hand soldering: 30 W, within 5 s
2. Dip soldering: 240°C, within 3 s
Wait for one minute after soldering before exerting any external
force on the solder.
Use non-corrosive resin fluid as the flux.
Make sure that the electric cord is wired so that it does not touch
the Unit. If the electric cord will touch the Unit, then electric wires
with a heat resistance of 100°C min. must be used.
After wiring the Switch, maintain an appropriate clearance and
creepage distance.
Operating Environment
The IP65 model is designed with a protective structure so that it
will not sustain damage if it is subjected to water from any
direction to the front of the panel.
Using the Microload
Insert a contact protection circuit, if necessary, to prevent the
reduction of life expectancy due to extreme wear on the contacts
caused by loads where inrush current occurs when the contact is
opened and closed.
The A16 allows both a general-purpose load (125 V at 5A, 250 V
at 3 A) and a microload. If a general-purpose load is applied,
however, the microload area cannot be used. If the microload
area is used with a general-purpose load, the contact surface will
become rough, and the opening and closing of the contact for a
microload may become unreliable.
The minimum applicable load is the N-level reference value. This
value indicates the malfunction reference level for the reliability
level of 60% (λ 60) (conforming to JIS C5003).
The equation, λ 60 = 0.5 x 10
malfunction rate is less than 1/2,000,000 with a reliability level of
60%.
Do not apply a voltage between the incandescent lamp and
the terminal that is greater than the rated voltage. If the incan-
descent lamp is broken, the operating part may pop out.
Always turn OFF the power and wait for 10 minutes before
replacing the incandescent lamp. If the lamp is replaced
immediately after the power is turned OFF, the remaining heat
may cause burns.
2
). Perform soldering according to the conditions provided
!
WARNING
- -4
/time indicates that the estimated
22
LEDs
The LED current-limiting resistor is built-in, so internal resistance
is not required.
Others
The oil-resistant IP65 uses NBR rubber and is resistant to
general cutting oil and cooling oil. Some particular oils cannot be
used with the oil-resistant IP65, however, so contact your
OMRON representative for details.
If the panel is to be finished with coating, etc., make sure that the
panel meets the specified dimensions after the coating.
Do not subject the Switch to extreme shock or vibration. Doing so
will cause malfunctions and damage to the Switch.
Do not let sharp objects come into contact with the Switches that
are made of resin. Doing so will damage the Switches, causing
scratches on the outside of the operating parts, and malfunction.
When handling the Switches, do not throw or drop them.
Rated voltage
5 VDC
12 VDC
24 VDC
Hammer Screwdriver
Invalid
area
Microload area
General-purpose load area
Area of use
Current (mA)
Do not allow the Switch
to drop and hit the
ground.
Do not place or drop
heavy objects on the
Switch.
Do not operate the Switch
with hard or sharp objects.
Internal limiting resistor
33 Ω
270 Ω
1600 Ω