HLMP-CW15-VY000 Avago Technologies US Inc., HLMP-CW15-VY000 Datasheet
![LED 5MM INGAN WHITE 15DEG](/photos/22/93/229339/4533197_sml.jpg)
HLMP-CW15-VY000
Specifications of HLMP-CW15-VY000
HLMP-CW15-VY000
Related parts for HLMP-CW15-VY000
HLMP-CW15-VY000 Summary of contents
Page 1
... Data Sheet HLMP-CB11, HLMP-CB12, HLMP-CM11, HLMP-CM12, HLMP-CE11, HLMP-CE12, HLMP-CB26, HLMP-CB27, HLMP-CM26, HLMP-CM27, HLMP-CE26, HLMP-CE27, HLMP-CB36, HLMP-CB37, HLMP-CM36, HLMP-CM37, HLMP-CE36, HLMP-CE37 Description These high intensity blue, green, and cyan LEDs are based on the most efficient and cost effective InGaN material technology. The 470 nm typical dominant wavelength for blue and 525 nm typical wavelength for green is well suited to color mixing in full color signs ...
Page 2
Package Dimensions Package A 1.14 ± 0.20 (0.045 ± 0.008) 4.90 ± 0.20 (0.193 ± 0.008) 8.61 ± 0.20 (0.339 ± 0.008) Package B 1.14 ± 0.20 (0.045 ± 0.008) 4.90 ± 0.20 NOTE 1 (0.192 ± 0.008) 8.61 ± 0.20 (0.339 ± 0.008) DIMENSION H DIMENSION H: 15° = 10.80 ± 0.25 mm (0.425 ± 0.01 INCH) 23° = 10.00 ± 0.25 mm (0.394 ± 0.01 INCH) 30° = 11.27 ± 0.25 mm (0.444 ± 0.01 INCH) NOTES: 1. MEASURED JUST ABOVE FLANGE. 2. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES). 3. EPOXY MENISCUS MAY EXTEND ABOUT 1 mm (0.040") DOWN THE LEADS HEAT SINKING APPLICATION IS REQUIRED, THE TERMINAL FOR HEAT SINK IS ANODE. 2.35 (0.093) MAX. 0.70 (0.028) MAX. CATHODE LEAD 31.60 MIN. (1.244) 1.50 ± 0.15 ...
Page 3
... HLMP-CB6-SV0xx Blue HLMP-CB6-TUDxx Blue HLMP-CB7-SV0xx Blue HLMP-CM6-X10xx Green HLMP-CM6-YZCxx Green HLMP-CM7-X10xx Green HLMP-CE6-WZ0xx Cyan HLMP-CE7-WZ0xx Cyan HLMP-CB6-QT0xx Blue HLMP-CB6-RSBxx Blue HLMP-CB7-RU0xx Blue HLMP-CB7-RSDxx Blue HLMP-CM6-X10xx Green HLMP-CM6-XYCxx Green HLMP-CM7-X10xx Green HLMP-CM7-XYCxx Green HLMP-CM7-XYDxx Green HLMP-CE6-WZ0xx Cyan HLMP-CE7-WZ0xx Cyan Notes: 1. Tolerance for luminous intensity measurement is ±15%. ...
Page 4
... Part Numbering System HLMP - x x xx - x x x Mechanical Options 00: Bulk DD: Ammo Pack Color Bin Options 0: Full Color Bin Distribution B: Color Bin 2 and 3 C: Color Bin 3 and 4 D: Color Bin 4 and 5 Maximum Intensity Bin ...
Page 5
Absolute Maximum Rating Parameters [1] DC Forward Current [] Peak Pulsed Forward Current Power Dissipation LED Junction Temperature Operating Temperature Range Storage Temperature Range Notes: 1. Derate linearly as shown in Figure . . Duty factor 10%, frequency 1 KHz. Electrical/Optical Characteristics Parameters Symbol Min. Typ. Max. ...
Page 6
CYAN 0.8 GREEN BLUE 0.6 0.4 0.2 0 380 430 480 530 580 630 680 WAVELENGTH – nm Figure 1. Relative intensity vs. wavelength 1.0 2.0 3.0 4.0 FORWARD VOLTAGE – V Figure 3. Forward ...
Page 7
ANGULAR DISPLACEMENT – DEGREES Figure 6. Spatial radiation pattern for Cx11 and Cx12 1 0.5 0 -90 -60 -30 0 ANGULAR DISPLACEMENT – DEGREES Figure 7. Spatial radiation pattern for Cx26 and Cx27 1 0.5 0 -90 -60 -30 ...
Page 8
Intensity Bin Limit Table Intensity (mcd Bin Min Max N 680 880 P 880 1150 Q 1150 1500 R 1500 1900 S 1900 500 T 500 00 U 00 400 V 400 5500 W 5500 700 X 700 900 Y ...
Page 9
Precautions Lead Forming • The leads of an LED lamp may be preformed or cut to length prior to insertion and soldering on PC board. • If lead forming is required before soldering, care must be taken to avoid any ...
Page 10
Recommended Wave Soldering Profile TURBULENT WAVE 250 200 150 FLUXING 100 50 30 PREHEAT TIME – SECONDS Ammo Packs Drawing 6.35 ± 1.30 (0.25 ± 0.0512) 9.125 ± 0.625 (0.3593 ± 0.0246) 18.00 ± 0.50 (0.7087 ± 0.0197) 12.70 ± 0.30 (0.50 ± 0.0118) ALL DIMENSIONS IN MILLIMETERS (INCHES). NOTE: THE AMMO-PACKS DRAWING IS APPLICABLE FOR PACKAGING OPTION -DD & -ZZ AND REGARDLESS OF STANDOFF OR NON-STANDOFF. 10 LAMINAR WAVE BOTTOM ...
Page 11
Packaging Box for Ammo Packs FROM LEFT SIDE OF BOX, ADHESIVE TAPE MUST BE FACING UPWARD. ANODE LEAD LEAVES THE BOX FIRST. NOTE: FOR InGaN DEVICE, THE AMMO PACK PACKAGING BOX CONTAINS ESD LOGO. DISCLAIMER AVAGO’S PRODUCTS AND SOFTWARE ARE NOT SPECIFICALLY DESIGNED, MANUFACTURED OR AUTHORIZED FOR SALE AS PARTS, COMPONENTS OR ASSEMBLIES FOR THE PLANNING, CONSTRUCTION, MAINTENANCE OR DIRECT OPERATION OF ...