LTL-307Y Lite-On Electronics, LTL-307Y Datasheet
LTL-307Y
Specifications of LTL-307Y
LTL-307Y
Q1280446
Available stocks
Related parts for LTL-307Y
LTL-307Y Summary of contents
Page 1
... All dimensions are in millimeters (inches). 2. Tolerance is ± 0.25mm(.010") unless otherwise noted. 3. Protruded resin under flange is 1.0mm(.04") max. 4. Lead spacing is measured where the leads emerge from the package. 5. Specifications are subject to change without notice. Part No. : LTL-307Y BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION Lens ...
Page 2
... Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) DC Forward Current Derating Linear From 50 ℃ Reverse Voltage Operating Temperature Range Storage Temperature Range Lead Soldering Temperature [2 mm(.0787") From Body] Part No. : LTL-307Y BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION =25 ℃ ℃ ℃ ℃ A Maximum Rating ...
Page 3
... The dominant wavelength, λ wavelength which defines the color of the device. 4. The Iv guarantee should be added ± 15% . Part No. : LTL-307Y BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION =25 ℃ ℃ ℃ ℃ A Symbol Min ...
Page 4
... LITE-ON TECHNOLOGY CORPORATION Typical Electrical / Optical Characteristics Curves (25 ℃ Ambient Temperature Unless Otherwise Noted) Part No. : LTL-307Y BNS-OD-C131/ Page : ...
Page 5
... Quantity is 1000 , 500 , 200 and 100 pcs per packing bag Quantity per inner carton total 8000 pcs per inner carton 8 Inner cartons per outer carton total 64000 pcs per outer carton In every shipping lot, only the last pack will be non-full packing Part No. : LTL-307Y BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION Packing Spec ...
Page 6
... Bin Table Specifications Luminous Intensity Unit : mcd @10mA Bin Code Note: Tolerance of measurement precision is ±15% Part No. : LTL-307Y BNS-OD-C131/A LITE-ON TECHNOLOGY CORPORATION Min 12.6 8.7 Max. 100 12.6 Page : ...
Page 7
... Max. (one time only) Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or catastrophic failure of the LED. IR reflow is not suitable process for through hole type LED lamp product. Part No. : LTL-307Y BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION CAUTIONS Wave soldering ...
Page 8
... To verify for ESD damage, check for “light up” and Vf of the suspect LEDs at low currents. The Vf of “good” LEDs should be >2.0V@0.1mA for InGaN product and >1.4V@0.1mA for AlInGaP product. Part No. : LTL-307Y BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION ...
Page 9
... Corrective action from previous audits completed? 3. Are audit records complete and on file? 8. Others White LED is materialized by combining blue LED and phosphors. Color of White LED by an operating current. The appearance and specifications of the product may be modified for improvement, without prior notice. Part No. : LTL-307Y BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION ...
Page 10
... Environmental Test Solder Resistance Solderability 9. Others The appearance and specifications of the product may be modified for improvement, without prior notice. Part No. : LTL-307Y BNS-OD-C131/ Test Condition Ta= Under Room Temperature As Per Data Sheet Maximum Rating *Test Time= 1000HRS (-24HRS,+72HRS) *Test Current = 20 mA Max. ...