LTL-307G Lite-On Electronics, LTL-307G Datasheet - Page 7

• Manufacturer Part Number: LTL-307G
• Description: LED 5MM GREEN DIFFUSED
• Manufacturer: Lite-On Electronics
• Type: Uni-Colorr

Specifications of LTL-307G

• Led Size: T-1 3/4
• Illumination Color: Green
• Lens Color/style: Diffused
• Operating Voltage: 2.6 V
• Wavelength: 565 nm
• Operating Current: 30 mA
• Lens Shape: Dome
• Mounting Style: Through Hole
• Viewing Angle: 50°
• Package / Case: Radial - 2 Lead
• Color: Green
• Millicandela Rating: 19mcd
• Current - Test: 10mA
• Wavelength - Dominant: 569nm
• Wavelength - Peak: 565nm
• Voltage - Forward (vf) Typ: 2.1V
• Lens Type: Diffused, Green Tinted
• Lens Style/size: Round, 5mm, T-1 3/4
• Height: 8.60mm
• Mounting Type: Through Hole
• Resistance Tolerance: 569nm
• Package Type: T-1 3/4
• Emitting Color: Yellow Green
• Luminous Intensity: 19mcd
• Test Current (it): 10mA
• Forward Current: 30mA
• Dominant Wave Length: 569nm
• Forward Voltage: 2.6V
• Product Length (mm): 5.85mm
• Product Height (mm): 8.6mm
• Product Depth (mm): 5.85mm
• Mounting: Through Hole
• Peak Wavelength: 565nm
• Shape Type: Circular
• Chip Material: GaP
• Main Category: Standard LED
• Number Of Elements: 1
• Pin Count: 2
• Operating Temperature Classification: Industrial
• Operating Temp Range: -55C to 100C
• Reverse Voltage: 5V
• Power Dissipation: 100mW
• Lens Dimensions: 5x5x7.6mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Luminous Flux @ Current - Test: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 160-1706

1. Application
2. Storage
3. Cleaning
4. Lead Forming & Assembly
5. Soldering
BNS-OD-C131/A4
Part No. : LTL-307G
During lead forming, the leads should be bent at a point at least 3mm from the base of LED lens.
Do not use the base of the lead frame as a fulcrum during forming.
Lead forming must be done before soldering, at normal temperature.
During assembly on PCB, use minimum clinch force possible to avoid excessive mechanical stress.
When soldering , For Lamp without stopper type and must be leave a minimum of 3 mm clearance
The storage ambient for the LEDs should not exceed 30°C temperature or 70% relative humidity.
It is recommended that LEDs out of their original packaging are used within three months.
For extended storage out of their original packaging, it is recommended that the LEDs be stored
in a sealed container with appropriate desiccant or in desiccators with nitrogen ambient.
Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LEDs if necessary.
from the base of the lens to the soldering point. To avoided the Epoxy climb up on lead frame and
was impact to non-soldering problem , Dipping the lens into the solder must be avoided.
Do not apply any external stress to the lead frame during soldering while the LED is at high temperature.
Recommended soldering conditions :
The LEDs described here are intended to be used for ordinary electronic equipment (such as office
equipment,
for information on applications in which exceptional reliability is required, particularly when the failure or
malfunction of the LEDs may directly jeopardize life or health (such as in aviation, transportation, traffic
control equipment, medical and life support systems and safety devices).
Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or
Temperature
Soldering time
product.
catastrophic failure of the LED. IR reflow is not suitable process for through hole type LED lamp
Soldering iron
communication equipment and household applications).Consult Liteon’s Sales in advance
300°C Max.
3 sec. Max.
(one time only)
LITE-ON TECHNOLOGY CORPORATION
CAUTIONS
P r o p e r t y o f L i t e - O n O n l y
Pre-heat
Pre-heat time
Solder wave
Soldering time
Wave soldering
100°C Max.
60 sec. Max.
260°C Max.
5 sec. Max.
Page :
7
of
10