LXM1622-12-01 Microsemi Analog Mixed Signal Group, LXM1622-12-01 Datasheet - Page 5

• Manufacturer Part Number: LXM1622-12-01
• Description: MOD INVERTER CCFL DIM DUAL 5W
• Manufacturer: Microsemi Analog Mixed Signal Group
• Series: LXM1622r
• Type: Inverters for CCFL and UV Lampsr

Specifications of LXM1622-12-01

• Voltage - Input: 12V
• Output: 1800V
• Size / Dimension: 4.88" L x 1.26" W x 0.30" H (124mm x 32mm x 7.6mm)
• Mounting Type: Chassis Mount
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Copyright © 2000
Rev. 1.0, 2005-02-07
HIGHLIGHTS (CONTINUED)
•
In applications with no access to a vertical sync, an onboard
oscillator operates the inverter burst rate at about 270Hz. In
this non-synchronous mode, minor display disturbances can
be found under certain video conditions. This performance
may
synchronization must be used when no disturbance can be
tolerated.
0 < P.W. < 100% of period
0
V
I N T E G R A T E D
be
SYNC
Figure 5A - PW M Brightness Control
PW M Signal
from System
1mS to 200µS
2.5 -
5V
acceptable
BRITE RTN
P.W .
SLEEP
BRITE
Figure 5 - Brightness Control
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: [phone]
LXM1622-12-xx
V
H O W T H E R A N G E M A X W O R K S ( C O N T I N U E D )
for
SYN C
LXM1622-12-xx
BRITE
P R O D U C T S
many
+12V
GND
V
IN
D C
applications,
T Y P I C A L A P P L I C A T I O N
V
V
LO
Integrated Products
HI
Microsemi
RangeMAX™
CCF
TUB
but
•
•
•
•
•
•
D
UAL
The Brightness control may be a voltage output DAC,
digital resistor or a simple 10K potentiometer, or other
voltage source, as shown in Figure 5. A 2.5V to 5V Logic
Level PWM signal from a micro-controller may also be
used as shown in Figure 5A.
If synchronization to the video frame rate is desired,
connect the vertical sync pulse from the system video
controller to the V
is desired, connect V
If you need to turn the inverter ON/OFF remotely, connect
a 2.5V to 5V logic signal to the
ON/OFF is not needed, connect the
or other voltage source between 2.5V and 5V.
Connect V
V
Never connect V
lamp current regulation. If both lamp wires have heavy
high voltage insulation, connect the longest wire to V
This wire is typically white.
Also available in single lamp inverters LXM1612-xx-
xx, 5V dual LXM1622-05-xx and Quad Output
LXM1641-01 versions for multiple lamp applications.
Separate feedback loops for lamp current and open circuit
voltage regulation insure reliable strike under all operating
conditions, automatic over-voltage prevention with broken
or failed lamps, and accurate lamp current regulation.
A single input will accommodate negative and positive
vertical sync pulses at any pulse width.
LO
5W, D
to the low voltage wire (wire with thinner insulation).
P
RODUCTION
IGITAL
R a n g e M A X I N V E R T E R S
HI
to high voltage wire from the lamp. Connect
Not recommended for new design
D
IMMING
LO
SYNC
SYNC
to circuit ground as this will defeat
input. If no video synchronization
D
CCFL I
ATA
to ground.
S
LXM1622-12-xx
NVERTER
HEET
SLEEP
SLEEP
M
input. If remote
ODULE
input to V
Page 5
LO
IN
.