B81123C1152M EPCOS Inc, B81123C1152M Datasheet
B81123C1152M
Specifications of B81123C1152M
B81123C1152M000
Related parts for B81123C1152M
B81123C1152M Summary of contents
Page 1
... Film Capacitors EMI Suppression Capacitors (MKP) Series/Type: B81123 Date: May 2009 © EPCOS AG 2009. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. ...
Page 2
... EMI suppression capacitors (MKP 250 V AC Typical applications Y1 class for interference suppression "Line to ground" applications Climatic Max. operating temperature: 100 C Climatic category (IEC 60068-1): 40/100/21 Construction Dielectric: polypropylene (MKP) Internal series connection Plastic case (UL 94 V-0) Epoxy resin sealing (UL 94 V-0) ...
Page 3
... Capacitance tolerance code 20% Please read Cautions and warnings and Important notes at the end of this document. 22.5 mm Ordering code l (composition see below) 10.5 18.0 B81123C1102M*** 11.0 18.0 B81123C1152M*** 12.5 18.0 B81123C1222M*** 14.5 18.0 B81123C1332M*** 17.5 18.0 B81123C1472M*** 16.0 26.5 B81123C1562M*** 16.5 26 ...
Page 4
B81123 Y1 / 250 V AC Technical data Max. operating temperature T op,max Dissipation factor tan ( (upper limit values) Insulation resistance R ins or time constant = ins at 20 ...
Page 5
Pulse handling capability "dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal voltages, expressed "k " represents the maximum permissible pulse characteristic of the waveform applied to the 0 2 capacitor, expressed in ...
Page 6
... Before a solderability test is carried out, terminals are subjected to accelerated ageing (to IEC 60068-2-2, test Ba exposure to dry heat at 155 C). Since the ageing temperature is far higher than the upper category temperature of the capacitors, the terminal wires should be cut off from the capacitor before the ageing procedure to prevent the solderability being impaired by the products of any capacitor decomposition that might occur ...
Page 7
... Please read Cautions and warnings and Important notes at the end of this document. 2.0 +0/ 0.5 mm from capacitor body or seating plane Heat-absorbing board, (1.5 0.5) mm thick, between capacitor body and liquid solder No visible damage 2% for MKT/MKP/MFP 5% for EMI suppression capacitors As specified in sectional specification Page B81123 Y1 / 250 V AC ...
Page 8
... B81123 Y1 / 250 V AC 1.3 General notes on soldering Permissible heat exposure loads on film capacitors are primarily characterized by the upper cate- gory temperature T . Long exposure to temperatures above this type-related temperature limit max can lead to changes in the plastic dielectric and thus change irreversibly a capacitor's electrical characteristics ...
Page 9
... MKT, MKP, MFP (coated/boxed) Even when suitable solvents are used, a reversible change of the electrical characteristics may occur in uncoated capacitors immediately after they are washed. Thus it is always recommended to dry the components (e. before they are subjected to subsequent electrical test- ing. Table A ...
Page 10
... B81123 Y1 / 250 Embedding of capacitors in finished assemblies In many applications, finished circuit assemblies are embedded in plastic resins. In this case, both chemical and thermal influences of the embedding ("potting") and curing processes must be taken into account. Our experience has shown that the following potting materials can be recommended: non-flexible epoxy resins with acid-anhydride hardeners ...
Page 11
... IEC 60068-2-6. EPCOS offers film capacitors specially designed for operation under more severe vibration regimes such as those found in automotive applications. Consult our catalog "Film Capacitors for Automotive Electronics". Please read Cautions and warnings and Important notes at the end of this document. B81123 ...
Page 12
... Topic Safety information Soldering Do not exceed the specified time or temperature limits during soldering. Cleaning Use only suitable solvents for cleaning capacitors. 2 "Cleaning" Embedding of When embedding finished circuit assemblies in capacitors in plastic resins, chemical and thermal influences finished assemblies must be taken into account. ...
Page 13
Symbols and terms Symbol English Heat transfer coefficient Temperature coefficient of capacitance C A Capacitor surface area Humidity coefficient of capacitance C C Capacitance C Rated capacitance R C Absolute capacitance change C/C Relative capacitance change (relative deviation of actual ...
Page 14
B81123 Y1 / 250 V AC Symbol English I (Sinusoidal) alternating current, RMS root-mean-square value i Capacitance drift z k Pulse characteristic 0 L Series inductance S Failure rate Constant failure rate during useful 0 service life Failure rate, determined ...
Page 15
Symbol English V Category voltage C V Category AC voltage C,RMS V Corona-discharge onset voltage CD V Charging voltage voltage DC V Fly-back capacitor voltage FB V Input voltage i V Output voltage o V Operating voltage ...
Page 16
Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical ...