HFBR-53A5VFMZ Avago Technologies US Inc., HFBR-53A5VFMZ Datasheet
HFBR-53A5VFMZ
Specifications of HFBR-53A5VFMZ
Available stocks
Related parts for HFBR-53A5VFMZ
HFBR-53A5VFMZ Summary of contents
Page 1
... HFBR-53A5VEMZ/HFBR-53A5VFMZ 3 Fiber Optic Transceivers for Gigabit Ethernet Low Voltage Data Sheet Description The HFBR-53A5VEMZ transceivers from Avago Technolo- gies allow the system designer to implement a range of solutions for multimode Gigabit Ethernet applications. The overall Avago transceiver product consists of three sections: the transmitter and receiver optical sub- ...
Page 2
... The HFBR-53A5VEMZ/FMZ is compatible with industry- standard wave or hand solder processes. Process Plug This transceiver is supplied with a process plug (HFBR-5000) for protection of the optical ports within the duplex SC connector receptacle. This process plug prevents contamination during wave solder and aqueous rinse as well as during handling, shipping and storage made of a high-temperature, molded sealing material that can withstand 80° ...
Page 3
... Connection of the HFBR-53A5VEMZ/FMZ to a non- approved optical source, operating above the recom- mended absolute maximum conditions or operating the HFBR-53A5VEMZ/FMZ in a manner inconsistent with its design and function may result in hazardous radiation exposure and may be considered an act of modifying or manufacturing a laser product. The person(s) per- ...
Page 4
... For an optical transmitter device to be eye-safe in the event of a single fault failure, the transmitter must either maintain normal, eye-safe operation or be disabled. In the HFBR-53A5VEMZ/FMZ there are three key elements to the laser driver safety circuitry: a monitor diode, a window detector circuit, and direct control of the laser bias ...
Page 5
Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause catastrophic damage to the device. Limits apply to each parameter in isolation, all other parameters having values within the recommended operating conditions. It should not be assumed ...
Page 6
... HFBR-53A5VEMZ/FMZ, 850 nm VCSEL Transmitter Electrical Characteristics (T = 0˚C to +70˚ Parameter Supply Current Power Dissipation Laser Reset Voltage Receiver Electrical Characteristics (T = 0˚C to +70˚ Parameter Supply Current Power Dissipation Data Output Voltage – Peak to Peak Differential Data Output Rise Time Data Output Fall Time Signal Detect Output Voltage – Low Signal Detect Output Voltage – High Signal Detect Assert Time Signal Detect Deassert Time ...
Page 7
... HFBR-53A5VEMZ/FMZ, 850 nm VCSEL Transmitter Optical Characteristics (T = 0°C to +70° Parameter O utput Optical Power 50/125 µ 0.20 Fiber Output Optical Power 62.5/125 µ 0.275 Fiber Optical Extinction Ratio Center Wavelength Spectral Width – rms O ptical Rise/Fall Time RIN 12 C oupled Power Ratio T otal Transmitter Jitter Added at TP2 Receiver Optical Characteristics (T = 0°C to +70° Parameter ...
Page 8
Table 1. Pinout Table Pin Symbol Functional Description M ounting Pins The mounting pins are provided for transceiver mechanical attachment to the circuit board. They are embedded in the nonconductive plastic housing and are not connected to the trans ceiver internal circuit, nor is there a guaranteed connection to the metallized housing in the EM and FM versions. They should be soldered into plated-through holes on the printed circuit board Receiver Signal Ground EER Directly connect this pin to receiver signal ground plane RD+ Receiver Data Out AC coupled – PECL compatible. 3 RD– Receiver Data Out Bar ...
Page 9
... USE SURFACE-MOUNT COMPONENTS FOR OPTIMUM HIGH-FREQUENCY PERFORMANCE. USE 50 Ω MICROSTRIP OR STRIPLINE FOR SIGNAL PATHS. LOCATE 50 Ω TERMINATIONS AT THE INPUTS OF RECEIVING UNITS. Figure 3. Recommended Gigabit/sec Ethernet HFBR-53A5VEMZ/FMZ fiber-optic transceiver and HDMP-1636A/1646A SERDES integrated circuit transceiver interface and power supply filter circuits 20.32 ...
Page 10
... DIMENSIONS ARE IN MILLIMETERS (INCHES). ALL DIMENSIONS ARE ± 0.025 mm UNLESS OTHERWISE SPECIFIED. Figure 5. Package outline for HFBR-53A5VEMZ 10 39.6 (1.56) MAX. RESERVED PROCESS 10.2 MAX. (0.40) MAX. 20.32 (0.80) 29.6 UNCOMPRESSED (1 ...
Page 11
... PCB BOTTOM VIEW Figure 6. Suggested module positioning and panel cut-out for HFBR-53A5VEMZ 11 1.014 2x 0.8 2x (0.032) 5.35 27.4 ± 0.50 9.4 (0.25) (1.08 ± 0.02) (0.374) MODULE PROTRUSION 0.8 (0.032) + 0.5 10.9 – 0. 0.02 0.43 – 0.01 ...
Page 12
... DIMENSIONS ARE IN MILLIMETERS (INCHES). ALL DIMENSIONS ARE ± 0.025 mm UNLESS OTHERWISE SPECIFIED. Figure 7. Package outline for HFBR-53A5VFMZ 1 39.6 (1.56) MAX. 1.01 (0.40) 25.8 MAX. (1.02) 10.2 MAX. (0.40) 9.8 MAX. 22.0 (0 ...
Page 13
... BOTTOM SIDE OF PCB DIMENSIONS ARE IN MILLIMETERS (INCHES). ALL DIMENSIONS ARE ± 0.025 mm UNLESS OTHERWISE SPECIFIED. Figure 8. Suggested module positioning and panel cut-out for HFBR-53A5VFMZ Ordering Information 850 nm VCSEL (SX – Short Wavelength Laser) HFBR-53A5VEMZ Extended shield, metal housing. HFBR-53A5VFMZ Flush shield, metal housing. ...
Page 14
For product information and a complete list of distributors, please go to our website: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries. Data subject to change. Copyright © ...