HFBR-57E0APZ Avago Technologies US Inc., HFBR-57E0APZ Datasheet - Page 14

• Manufacturer Part Number: HFBR-57E0APZ
• Description: TXRX MM SFP LC CONN BAIL DELATCH
• Manufacturer: Avago Technologies US Inc.
• Series: -r

Specifications of HFBR-57E0APZ

• Applications: Ethernet
• Mounting Type: SFP
• Voltage - Supply: 2.97 V ~ 3.63 V
• Connector Type: LC Duplex
• Wavelength: 1300nm
• Data Rate: 155MBd
• Supply Voltage: 3.3V
• Wavelength Typ: 1300nm
• Leaded Process Compatible: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Receiver Optical and Electrical Characteristics
HFBR-57E0LZ /PZ(T
HFBR-57E0ALZ/APZ (T
Notes:
11a. Systematic Jitter contributed by the transmitter is defined as the combination of Duty Cycle Distortion and Data Dependent Jitter.
11b. Duty Cycle Distortion contributed by the transmitter is measured at the 50% threshold of the optical output signal using an IDLE Line
11c. Data Dependent Jitter contributed by the transmitter is specified with the FDDI test pattern described in FDDI PMD Annex A.5.
12a. Random Jitter contributed by the transmitter is specified with a 155.52 MBd (77.5 MHz square-wave) input signal.
12b. Random Jitter contributed by the transmitter is specified with an IDLE Line State, 125 MBd (62.5 MHz square-wave) input signal. See
Parameter
Input Optical Power minimum at Window Edge
Input Optical Power at Eye Center
Input Optical Power Maximum
Duty Cycle Distortion Contributed by the Receiver
FE
Data Dependent Jitter Contributed by the Receiver
FE
Random Jitter Contributed by the Receiver
Loss of Signal - Deasserted
Loss of Signal - Asserted
Loss of Signal - Hysteresis
Loss of Signal Deassert Time (on to off)
Loss of Signal Assert Time (off to on)
Notes:
13a. This specification is intended to indicate the performance of the receiver section of the transceiver when Input Optical Power signal
14
Operating Wavelength
Systematic Jitter Contributed by the Receiver
OC-3
FE
OC-3
FE
OC-3
FE
OC-3
OC-3
FE
OC-3
FE
-
-
-
-
-
Systematic Jitter is measured at 50% threshold using a 155.52 MBd (77.5 MHz square-wave), 2
signal.
State, 125 MBd (62.5 MHz square-wave), input signal.
Application Information - Transceiver Jitter Performance Section of this data sheet for further details.
characteristics are present per the following definitions. The Input Optical Power dynamic range from the minimum level (with a window
time-width) to the maximum level is the range over which the receiver is guaranteed to provide output data with a Bit Error Rate (BER)
better than or equal to 1 x 10
At the Beginning of Life (BOL)
Over the specified operating temperature and voltage ranges
Input is a 155.52 MBd, 2
Appendix I.
Receiver data window time-width is 1.23 ns or greater for the clock recovery circuit to operate in. The actual test data window time-
width is set to simulate the effect of worst case optical input jitter based on the transmitter jitter values from the specification tables.
The test window time-width is 3.32 ns.
Transmitter operating with a 155.52 MBd, 77.5 MHz square-wave, input signal to simulate any cross-talk present between the transmitter
and receiver sections of the transceiver.
C
= 0 ºC to +70 ºC, V
C
= -40 ºC to +85 ºC, V
23
-1 PRBS data pattern with 72 “1” s and 72 “0”s inserted per the CCITT (now ITU-T) recommendation G.958
-10.
CC
P
P
P
DCD
DDJ
RJ
P
P
P
Symbol
SJ
l
IN MIN
IN MIN
IN MAX
A
D
A
= 2.97 V to 3.63 V)
- P
CC
D
(W)
(C)
= 2.97 V to 3.63 V)
Minimum
-14
-14
1270
P
-45
1.5
0
0
D
+ 1.5 dB
Typical
0.11
0.08
0.02
0.14
0.14
2
5
Maximum
-30
-31
-31
-31.8
1380
1.2
0.4
1.0
1.91
2.14
-31
-33
100
350
23
- 1 psuedorandom data pattern input
Units
dBm avg
dBm avg
dBm avg
nm
ns p-p
ns p-p
ns p-p
ns p-p
dBm avg
dBm avg
dB
µs
µs
Notes
13a, Figure 4
13b
14a, Figure 4
14b
13a
13b
15a
15b
15c
16a
16b
17
18
19
20