HFBR-57E0LZ Avago Technologies US Inc., HFBR-57E0LZ Datasheet
HFBR-57E0LZ
Specifications of HFBR-57E0LZ
Available stocks
Related parts for HFBR-57E0LZ
HFBR-57E0LZ Summary of contents
Page 1
... V TTL LOS output • Receiver outputs are squelch enabled • Manufactured in an ISO 9001 certified facility • Temperature range: 0 °C to +70° C HFBR-57E0LZ/PZ: -40 °C to +85 °C HFBR-57E0ALZ/APZ: • Bail de-latch option Applications • OC-3 SFP transceivers are designed for ATM LAN and ...
Page 2
... HFBR-57E0. The connection diagram of the module is shown in Figure 2. Figures 5 and 7 depict the external configuration and dimensions of the module. Installation The HFBR-57E0 can be installed in or removed from any MultiSource Agreement (MSA) – compliant Small Form Pluggable port regardless of whether the host equipment OPTICAL INTERFACE ...
Page 3
... This protocol uses the 2-wire serial CMOS E2PROM protocol of the ATMEL AT24C01A or equivalent. The contents of the HFBR-57E0 serial ID memory are defined in Table 3 as specified in the SFP MSA. Functional Data I/O The HFBR-57E0 fiberoptic transceiver is designed to accept industry standard differential signals ...
Page 4
... Avago will be required to meet the requirements of FCC in the United States, CENELEC EN55022 (CISPR 22) in Europe and VCCI in Japan. The metal housing and shielded design of the HFBR-57E0 minimize the EMI challenge facing the host equipment designer. These transceivers provide superior EMI performance ...
Page 5
... SO+ 50 SO– 4 SerDes 10 µF 50 SI+ 50 SI– µH 1 µH 0.1 µF 10 µF 0.1 µF VccT HFBR-57E0 4 3 0.1 µF TD+ LED DRIVER & SAFETY TD– CIRCUITRY TX GND 0.1 µF 130 130 W VccR 3.3 V 0.1 130 130 µF 0.1 µF ...
Page 6
Table 2. Pin Description Pin Name Function/Description Transmitter Ground Disable Transmitter Disable- Module disables on high or open 4 MOD-DEF2 Module Definition 2 - Two Wire Serial ID Interface 5 MOD-DEF1 ...
Page 7
Table 3. EEPROM Serial ID Memory Contents Add Hex ASCII Add Note Note ...
Page 8
Table 3. EEPROM Serial ID Memory Contents (continued) Add Hex ASCII Add Notes: 1. Addresses specify a unique identifier. 2. Addresses specify ...
Page 9
... TRANSCEIVER CAGE 13.0±0.2 [0.512±0.008] AREA FOR PROCESS PLUG 6.6 [0.261] 13.50 [0.53] 14.8MAX. UNCOMPRESSED [0.583] AVAGO HFBR-57E0xxZ YYWW Country of Origin 13.4±0.1 [0.528±0.004] 55.2±0.2 [2.17±0.01] 0.7MAX. UNCOMPRESSED [0.028] 8.5±0.1 [0.335±0.004] DIMENSIONS ARE IN MILLIMETERS (INCHES) ...
Page 10
X Y 16.25 MIN. PITCH B PCB EDGE 5.68 8.58 11.08 16.25 REF . 14.25 2.0 11x 3 5 3.2 0.9 20 PIN 1 10.93 9.6 0.8 TYP . 1.55 ± 0.05 ∅ 0 ...
Page 11
PCB [1.64±.02] 15MAX .59 CAGE ASSEMBLY 12.4REF .49 9.8MAX .39 Figure 9. SFP Assembly Drawing 11 1.7±0.9 [.07±.04] AREA BEZEL FOR PROCESS PLUG Tcase REFERENCE POINT 10REF 1.15REF .39 .05 TO PCB BELOW PCB 0.4±0.1 [.02±0.004] BELOW ...
Page 12
... HFBR-57E0ALZ/APZ (T = -40 ºC to +85 º Parameter Supply Current Power Dissipation Transmitter Disable (TX Disable) High Transmitter Disable (TX Disable) Low Receiver Electrical Characteristics HFBR-57E0LZ/ ºC to +70 º HFBR-57E0ALZ/APZ (T = -40 ºC to +85 º Parameter Supply Current Power Dissipation Data Output: Receiver Differential Output Voltage ...
Page 13
... Data and Data-bar outputs are squelched at LOS assert level. When the received light drops below LOS assert point, it will force receiver data and data-bar steady PECL levels High and Low respectively. 7. The data output rise and fall times are measured between 20% and 80% levels. Transmitter Optical Characteristics HFBR-57E0LZ/PZ ºC to +70 º HFBR-57E0ALZ/APZ (T = -40 ºC to +85 ºC, V ...
Page 14
... Random Jitter contributed by the transmitter is specified with an IDLE Line State, 125 MBd (62.5 MHz square-wave) input signal. See Application Information - Transceiver Jitter Performance Section of this data sheet for further details. Receiver Optical and Electrical Characteristics HFBR-57E0LZ /PZ ºC to +70 º HFBR-57E0ALZ/APZ (T = -40 º ...
Page 15
... Data Out and Data Out Bar go to steady PECL levels High and Low respectively. 21. The HFBR-57E0 transceiver complies with the requirements for the trade-offs between center wavelength, spectral width, and rise/fall times shown in Figure 3. This figure is derived from the FDDI PMD standard (ISO/IEC 9314-3 : 1990 and ANSI X3.166 - 1990) per the description in ANSI T1E1 ...
Page 16
... Bail de-latch 1300 nm LED (Operating Case Temperature -40 °C to +85 °C) HFBR-57E0ALZ Standard de-latch HFBR-57E0APZ Bail de-latch EEPROM contents and/or label options HFBR-57E0LZ-YYY Standard de-latch +70°C HFBR-57E0PZ-YYY Bail de-latch +70°C HFBR-57E0ALZ-YYY Standard de-latch, -40°C to +85°C HFBR-57E0APZ-YYY Bail de-latch, -40°C to +85°C Where " ...