FTLX1461E2 Finisar Corporation, FTLX1461E2 Datasheet
FTLX1461E2
Specifications of FTLX1461E2
Related parts for FTLX1461E2
FTLX1461E2 Summary of contents
Page 1
... Adaptable Power Supply (APS: +1.2 V) XAUI electrical interface - 4 x 3.125 Gb/s Ethernet Management and control via MDIO 2-wire bus 70-pin connector Separated signal/chassis ground PRODUCT SELECTION © Finisar Corporation – October 2008 Product Specification RoHS-6 Compliant FTLX1461E2 APPLICATIONS 10GBASE-LR 10G Ethernet FTLX1461E2 Rev B Page 1 ...
Page 2
... FTLX1461E2 Product Specification – October 2008 I. PIN DESCRIPTION Signal Name Level Management and Monitoring Ports MDIO Open Drain MDC 1.2 V CMOS PRTAD4 1.2 V CMOS PRTAD3 1.2 V CMOS PRTAD2 1.2 V CMOS PRTAD1 1.2 V CMOS PRTAD0 1.2 V CMOS LASI Open Drain RESET Open Drain ...
Page 3
... FTLX1461E2 Product Specification – October 2008 Receive Functions Reserved Reserved RX LANE 0+ AC-coupled, RX LANE 0– Internally biased differential RX LANE 1+ XAUI RX LANE 1– RX LANE 2+ RX LANE 2– RX LANE 3+ RX LANE 3– DC Power GND APS +1.2 V APS SENSE +1.2 V APS SET 3 ...
Page 4
... FTLX1461E2 Product Specification – October 2008 Electrical Pad Layout Fig 1-XENPAK Transponder Electrical Pad Layout II. Absolute Maximum Ratings Parameter Storage Ambient Temperature 1) Operating Case Temperature 1) Supply Voltage +5.0 V Supply Voltage +3.3 V Supply Voltage APS Static Discharge Voltage, All Pins 2) Average Receive Optical Power ...
Page 5
... FTLX1461E2 Product Specification – October 2008 III. Electrical Characteristics Recommended Operating Conditions Parameter Operating Case Temperature 1) Transponder Total Power Consumption Supply Voltage +5.0 V Supply Current +5.0 V Supply Voltage +3.3 V Supply Current +3.3 V Supply Voltage APS Supply Current APS 1) Worst case thermal location, see Figure 2. ...
Page 6
... FTLX1461E2 Product Specification – October 2008 Electrical AC Characteristics ( CC5 CC3 Parameter XAUI Input AC Characteristics (TXLANE[0..3]) Baud Rate Ethernet Baud Rate Tolerance Differential Input Impedance 1) Differential Return Loss 2) Input Differential Skew 3) Jitter Amplitude Tolerance XAUI Output AC Characteristics (RXLANE[0..3]) Baud Rate ...
Page 7
... FTLX1461E2 Product Specification – October 2008 IV. Optical Characteristics ( CC5 CC3 Parameter Transmitter Launch Power in OMA minus TDP Average Launch Power Center Wavelength Range Spectral Width (-20 dB) Side Mode Suppression Ratio Extinction Ratio Relative Intensity Noise OMA 12 Optical Modulation Aplitude (OMA) ...
Page 8
... FTLX1461E2 Product Specification – October 2008 Environmental Performance Operating case temperature: Operating humidity: Fibers and Connectors The transponder has SC receptacles for both Tx and Rx. The transponder is designed for single mode SC cables, 0° polished endface (PC). 70-pin Connector The module interface connector is a 70-pin, printed circuit board edge connection with a 0.5 mm pitch ...
Page 9
... FTLX1461E2 Product Specification – October 2008 Eye Safety Finisar FTLX1461E2 transponders are Class 1 Laser Products. They are certified per the following standards: Feature Agency Laser Eye FDA/CDRH Safety Laser Eye TÜV Safety Electrical TÜV Safety Electrical UL/CSA Safety Copies of the referenced certificates are available at Finisar Corporation upon request. ...
Page 10
... FTLX1461E2 Product Specification – October 2008 Package Outline Figure 2-XENPAK Mechanical Dimensions IX. References The following references are provided for informational purposes only. The parameters and operational behavior outlined in this specification describe the complete functionality of the 10G Transponder. Contact Finisar for any items concerning the operational characteristics of this device ...