FTL-8519-3D Finisar Corporation, FTL-8519-3D Datasheet
FTL-8519-3D
Specifications of FTL-8519-3D
Related parts for FTL-8519-3D
FTL-8519-3D Summary of contents
Page 1
... GBIC specification Rev. 5.5) • Fully metallic enclosure for low EMI • Low power dissipation • RoHS compliant and Lead Free Finisar’s FTL-8519-3D-2.5 850nm GBIC transceivers comply with GBIC Specification 1 Revision 5.5 . They are compatible with the Gigabit Ethernet as specified in IEEE Std 2 802 ...
Page 2
... FTL-8519-3D-2.5 2.125Gb/s GBIC Product Specification – November 2007 I. Pin Out Pin Name RX_LOS MOD_DEF(0) MOD_DEF(1) MOD_DEF(2) TX_DISABLE TX_FAULT (not supported) -RX_DAT +RX_DAT +TX_DAT -TX_DAT Table 1. GBIC to host connector pin assignment “Sequence” indicates the order in which pins make contact when the device is hot plugged. Also see “ ...
Page 3
... FTL-8519-3D-2.5 2.125Gb/s GBIC Product Specification – November 2007 II. Electrical Power Interface Finisar FTL-8519-3D-2.5 GBICs have an extended power supply voltage range described in Table 2. They are compatible with both 3.3V and 5 V systems. +5/3.3 Volt Electrical Power Interface Parameter Symbol Supply Current ...
Page 4
... FTL-8519-3D-2.5 2.125Gb/s GBIC Product Specification – November 2007 Low Speed Signal Parameters Parameter Symbol Min RX_LOS Assert Level RX_LOS Deassert Level RX_LOS Hysteresis RX_LOS Assert Delay t_loss_on RX_LOS Negate Delay t_loss_off TX_DISABLE Assert Time t_off TX_DISABLE Negate Time t_on TX_DISABLE Reset Time t_reset Table 4 ...
Page 5
... FTL-8519-3D-2.5 2.125Gb/s GBIC Product Specification – November 2007 V. Optical Parameters Optical Parameters Parameter Transmitter Center Wavelength Transmitter Spectral Width (RMS) Transmitter Optical Output Power Transmitter Extinction Ratio Relative Intensity Noise Transmitter Eye Opening Total Transmitter Jitter Transmitter Rise/Fall Time Optical Input Wavelength Optical Receiver Sensitivity < ...
Page 6
... PROM, see the Atmel data sheet titled “AT24C01A/02/04/08/16 2-Wire Serial CMOS PROM.” The FTL-8519-3D-2.5 also supports extended diagnostic features as described in Finisar Applications Note AN-2030, “Digital Diagnostic Monitoring Interface for Optical 8 Transceivers” , and additional information is available in SFF standard titled: “Digital Diagnostic Monitoring Interface for Optical Transceivers” ...
Page 7
... FTL-8519-3D-2.5 2.125Gb/s GBIC Product Specification – November 2007 Parameter Symbol Clock Speed Accuracy Internal Transceiver DD Temperature Temperature Internal Transceiver DD Voltage Supply Voltage Tx Bias Current DD Bias Tx Output Power DD TxPower Received Average DD RxPower Power Range Internal Transceiver DD Temperature Temperature Internal Transceiver DD Voltage Supply Voltage ...
Page 8
... FTL-8519-3D-2.5 2.125Gb/s GBIC Product Specification – November 2007 X. Mechanical Specifications Finisar GBICs are compatible with the mechanical specifications outlined in the GBIC Specification Revision 5.5, Section 6 Figure 1. GBIC Outline Drawing © Finisar Corporation November 16, 2007 Rev Page 8 ...
Page 9
... FTL-8519-3D-2.5 2.125Gb/s GBIC Product Specification – November 2007 XI. References 1. “Gigabit Interface Converter (GBIC) Revision 5.5”. Sun Microsystems Computer Company et. al., September 27, 2000. http://playground.sun.com/pub/OEmod/ 2. IEEE Std 802.3. IEEE Standards Department, 2002. 3. “Fibre Channel Physical and Signaling Interface (FC-PH, FC-PH2, FC-PH3)”. ...