HFBR-2412Z Avago Technologies US Inc., HFBR-2412Z Datasheet
![RECEIVER FIBER OPTIC 5MBD TTL ST](/photos/7/97/79724/hfbr-2412z_sml.jpg)
HFBR-2412Z
Specifications of HFBR-2412Z
Available stocks
Related parts for HFBR-2412Z
HFBR-2412Z Summary of contents
Page 1
... With the HFBR-24x6Z, the 125 MHz analog receiver, data rates 160 megabaud are attainable. Transmitters and receivers are directly compatible with popular “ ...
Page 2
... TX, standard power 4 TX, high power 2 RX, 5 MBd, TTL output 5 TX, high light output power 6 RX, 125 MHz, Analog Output HFBR-1412Z HFBR-1414MZ HFBR-1424Z HFBR-14E4Z HFBR-2412Z HFBR-2416MZ HFBR-24E2Z HFBR-24E6Z Fiber Size (μm) Evaluation Kit 200 HCS N/A 62.5/125 HFBR-0410Z 62.5/125 HFBR-0414Z 62.5/125 HFBR-0414Z 62 ...
Page 3
... Applications Support Guide This section gives the designer information necessary to use the HFBR-0400Z series components to make a func- tional fiber optic transceiver. Avago Technologies offers a wide selection of evaluation kits for hands-on experience with fiber optic products as well as a wide range of application notes complete with circuit diagrams and board layouts ...
Page 4
... HFBR-0400Z Series Evaluation Kits HFBR-0410Z ST Evaluation Kit Contains the following: x One HFBR-1412Z transmitter x One HFBR-2412Z five megabaud TTL receiver x Three meters of ST connectored 62.5/125 μm fiber optic cable with low cost plastic ferrules. x Related literature HFBR-0414Z ST Evaluation Kit Includes additional components to interface to the trans- mitter and receiver as well as the PCB to reduce design time ...
Page 5
... PINS 1,4,5,8 0.51 X 0.38 (0.020 X 0.015) PINS 2,3,6,7 0.46 DIA. (0.018) PIN NO. 1 INDICATOR Mechanical Dimensions - ST Port HFBR-x41xZ 12.7 (0.50) 27.2 (1.07) 12.7 (0.50) 3.81 (0.15) 2.54 (0.10) PINS 1,4,5,8 0.51 X 0.38 (0.020 X 0.015) PINS 2,3,6,7 ...
Page 6
... UNEF - 2A 3.81 (0.15) 2.54 DIA. (0.10) PINS 1,4,5,8 0.51 X 0.38 (0.020 X 0.015) PINS 2,3,6,7 0.46 DIA. (0.018) PIN NO. 1 INDICATOR Mechanical Dimensions - FC Port HFBR-x42xZ M8 x 0.75 6G THREAD (METRIC) 12.7 (0.50) 19.6 (0.77) 12.7 (0.50) 7.9 (0.31) 3.81 (0.15) 2.5 (0.10) 2.5 (0 ...
Page 7
... Mechanical Dimensions - SC Port HFBR-x4ExZ 3.81 (0.15) 7 28.65 (1.128) 12.7 (0.50) (0.394) 15.95 (0.628) 2.54 (0.10) 6.35 (0.25) 10.0 3.60 (0.140) 1.27 (0.050) 2.54 (0.100) 12.7 (0.500) 10.38 (0.409) 5.1 (0.200) ...
Page 8
... DIA. 6.61 DIA. 0.14 (0.260) (0.005) WASHER (Each HFBR-4401Z and HFBR-4411Z kit consists of 100 nuts and 100 washers). Port Cap Hardware HFBR-4402Z: 500 SMA Port Caps HFBR-4120Z: 500 ST Port Plugs (120 psi) 8 LED OR DETECTOR IC LENS–SPHERE (ON TRANSMITTERS ONLY) LENS–WINDOW ...
Page 9
... Compatible with all current makes of ST® multimode connectors x Mechanical dimensions are compliant with MIL-STD- 83522/13 x Maximum wall thickness when using nuts and wash- ers from the HFBR-4411Z hardware kit is 2.8 mm (0.11 inch) x Available on all ST ports Option C (Conductive Port Receiver Option) x Designed to withstand electrostatic discharge (ESD) of ...
Page 10
... Typical Link Data HFBR-0400Z Series Description The following technical data is taken from 4 popular links using the HFBR-0400Z series: the 5 MBd link, Ethernet 20 MBd link, Token Ring 32 MBd link, and the corresponds to transceiver solutions combining the HFBR-0400Z se- ries components and various recommended transceiver design circuits using off-the-shelf electrical components ...
Page 11
... MBd Logic Link Design If resistor R1 in Figure forward current applied to the HFBR-14x4Z LED transmitter. With the HFBR-14x4Z/24x2Z logic link is guaran- F teed to work with 62.5/125 μm fiber optic cable over the entire range 1750 meters at a data rate MBd, with arbitrary data format and pulse width distor- tion typically less than 25% ...
Page 12
... UNDERDRIVE - CABLE ATTENUATION -9 MAX (-40 °C, +85 °C) MIN (-40 °C, +85 °C) -10 TYP (+25 °C) - LINK LENGTH (km) Figure 3. HFBR-1414Z/HFBR-2412Z Link Design Limits with 62.5/125 μm Cable WORST CASE -40°C, +85°C UNDERDRIVE -2 TYPICAL 26°C UNDERDRIVE -3 -4 CABLE ATTENUATION α MAX (-40°C, +85°C) -5 α MIN (-40°C, +85°C) α ...
Page 13
... W TRANSMITTER FROM 1-METER P T TEST CABLE HFBR-2412Z RECEIVER Figure 8. System Propagation Delay Test Circuit and Waveform Timing Definitions. Ethernet 20 MBd Link (HFBR-14x4Z/24x6Z) (refer to Application Note 1038 for details) Typical Link Performance Parameter Symbol Receiver Sensitivity Link Jitter Transmitter Jitter Optical Power ...
Page 14
... Token Ring 32 MBd Link (HFBR-14x4Z/24x6Z) (refer to Application Note 1065 for details) Typical Link Performance Parameter Receiver Sensitivity Link Jitter Transmitter Jitter Optical Power Logic Level “0” Optical Power Logic Level “1” LED Rise Time LED Fall Time Mean Difference ...
Page 15
... The HFBR-14x4Z high power transmitter is optimized for small size fiber and typically can launch -15.8 dBm optical power into 50/125 μm fiber and -12 dBm into 62.5/125 μm fiber. The HFBR- 14x2Z standard transmitter typically can launch -12 dBm of optical power into 100/140 μm fiber cable ideal for large size fiber such as 100/140 μ ...
Page 16
... Optical Power Temperature Coefficient Thermal Resistance 14x2Z Numerical Aperture 14x4Z Numerical Aperture 14x2Z Optical Port Diameter 14x4Z Optical Port Diameter HFBR-14x2Z Output Power Measured Out of 1 Meter of Cable Parameter Symbol 50/125 Pm Fiber Cable P T50 62.5/125 Pm Fiber Cable P T62 100/140 Pm Fiber Cable ...
Page 17
... ST® precision ceramic ferrule (MILSTD- T 83522/13) for HFBR-1412Z/1414Z, and with an SMA 905 precision ceramic ferrule for HFBR-1402Z/1404Z. 6. When changing mW to dBm, the optical power is referenced (1000 mW). Optical Power P (dBm log P (mW)/1000 mW. ...
Page 18
... All HFBR-14XXZ LED transmitters are classified as IEC 825-1 Accessible Emission Limit (AEL) Class 1 based upon the current proposed draft scheduled effect on January 1, 1997. AEL Class 1 LED devices are considered eye safe. Contact your Avago Technologies sales representative for more information. CAUTION: The small junction sizes inherent to the design of these components increase the components’ susceptibility to damage from electrostatic discharge (ESD) ...
Page 19
... I F – FORWARD CURRENT – mA Figure 10. Normalized Transmitter Output vs. Forward Current. 0.1 μ Ω HIGH SPEED TEST OSCILLOSCOPE HEAD 3.0 2.0 1.4 1.0 0.8 0 -1.0 -2.0 -3.0 -4.0 -5.0 -7 100 +5 V HFBR-14x2Z/x4Z ...
Page 20
... HFBR-24x2Z Low-Cost 5 MBd Receiver Description The HFBR-24x2Z fiber optic receiver is designed to oper- ate with the Avago Technologies HFBR-14xxZ fiber optic transmitter and 50/125 μm, 62.5/125 μm, 100/ 140 μm, and 200 μm HCS® fiber optic cable. Consistent coupling into the receiver is assured by the lensed optical system (Figure 1). Response does not vary with fiber size d 0.100 μ ...
Page 21
Electrical/Optical Characteristics -40 ° °C unless otherwise specified Fiber sizes with core diameter d 100 μm and NA d 0.35, 4. Parameter High Level Output Current Low Level Output Voltage High Level Supply Current ...
Page 22
... A receiver dynamic range over temperature is achievable (assuming 10-9 BER). The frequency response is typically dc to 125 MHz. Although the HFBR-24x6Z is an analog receiver compatible with digital systems. Please refer to Applica- tion Bulletin 78 for simple and inexpensive circuits that operate at 155 MBd or higher. ...
Page 23
Absolute Maximum Ratings Parameter Storage Temperature Operating Temperature Lead Soldering Cycle Temp Time Supply Voltage Output Current Signal Pin Voltage Electrical/Optical Characteristics -40 °C to +85 °C; 4. Supply Voltage d 5. 511 :, Fiber sizes ...
Page 24
... V 100% 10. The conversion factor for the rise time to bandwidth is 0.41 since the HFBR-24x6Z has a second order bandwidth limiting characteristic. 0.1 μ Figure 14. Recommended ac Coupled Receiver Circuit. (See AB 78 and AN 1038 for more information.) CAUTION: The small junction sizes inherent to the design of these components increase the components’ susceptibility to damage from electrostatic discharge (ESD) ...
Page 25
FREQUENCY – Figure 15. Typical Spectral Noise Density vs. Frequency. 6.0 5 2.0 1.0 -60 -40 - ...