T-51944D104J-FW-A-AA Optrex America Inc, T-51944D104J-FW-A-AA Datasheet

Page 1

... HANDLING PRECAUTIONS FOR TFT-LCD MODULE -- PACKAGING SPECIFICATION -- PRODUCTS NUMBER LABELING FORMS -- LUMP UNIT FOR 10.4” SVGA T-51944D104J-FW-A-AA (AA) No. 2004-0189 Approved by (Quality Assurance Division) Checked by (ACI Engineering Division) Prepared by (ACI Engineering Division) Item OPTREX CORPORATION First Edition Dec 23, 2004 Final Revision ...

Page 2

... APPLICATION This specification applies to color TFT-LCD module, T-51944D104J-FW-A-AA. These specification papers are the proprietary product of OPTREX and include materials protected under copyright of OPTREX. No part of this document may be reproduced in any form or by any means without the express written permission of OPTREX. OPTREX does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a product specified in this document ...

Page 3

... OVERVIEW T-51944D104J-FW-A-AA is 10.4” color TFT-LCD (Thin Film Transistor Liquid Crystal Display) module composed of LCD panel, driver ICs, control circuit, and backlight unit. By applying 6 bit or 8 bit digital data, 800 × 600, 260 K-color or 16.7 M-color images are displayed on the 10.4” diagonal screen. Input power voltage is 3.3V for LCD driving. ...

Page 4

... Power Supply Voltage for LCD Power Supply Current for LCD Permissive Input Ripple Voltage *1) Power and signals sequence: t1 ≤ < t2 ≤ < t3 ≤ 0.9VCC LCD Power Supply Logic Signal 0.1VCC Backlight Power Supply T-51944D104J-FW-A-AA (AA) No. 2004-0189 SYMBOL VCC Note 1,2) op(Panel) T Note 2) ...

Page 5

... Lamp life time is defined as the time either when the brightness becomes 50% of the initial value, or when the starting lamp voltage does not meet the value specified in this table. *4) The life time of the backlight depends on the ambient temperature. The life time will decrease under low/high temperature. T-51944D104J-FW-A-AA (AA) No. 2004-0189 td =37.9 kHz, f =60 Hz, f ...

Page 6

... Please use the inverter which has symmetrical current wave form as follows, The degree of unbalance: less than 10% The ratio of wave height: less than I I CURRENT WAVE FORM T-51944D104J-FW-A-AA (AA) No. 2004-0189 2 ±10 High side peak PH PH The degree of unbalance = |I The ratio of wave height = I ...

Page 7

... Recommended wiring of Pin 17,18 (6 bit input) LVDS transmitter LOW data (2) CN 2(Backlight) Backlight-side connector: BHR-02(8.0)VS-1N (JST) Inverter-side connector: SM02(8.0)B-BHS(JST) Pin No. [Note] VBLH - VBLL = VL T-51944D104J-FW-A-AA (AA) No. 2004-0189 8 bit input +3.3 V Power supply +3.3 V Power supply GND GND R2, R3, R4, R5, R6, R7, G2 R2, R3, R4, R5, R6, R7, G2 GND ...

Page 8

... ISP data mapping a. ISP 6 bit compatibility mode(6 bit input) CLKIN+/- Link0+/- Link1+/- Link2+/- b. ISP 6 bit compatibility mode(8 bit input) CLKIN+/- Link0+/- Link1+/- Link2+/- Link3+/- c. ISP 8 bit compatibility mode CLKIN+/- Link0+/- Link1+/- Link2+/- Link3+/- T-51944D104J-FW-A-AA (AA) No. 2004-0189 DENA DENA DENA OPTREX CORPORATION ...

Page 9

... DENA (Data Enable) should always be positive polarity as shown in the timing specification. 3) DCLK should appear during all invalid period, and HD should appear during invalid period of frame cycle. 4) LVDS timing follows the timing specifications of LVDS receiver IC: THC63LVDF84B(Thine). ≥ HFP HBP CLK T-51944D104J-FW-A-AA (AA) No. 2004-0189 SYMBOL MIN TYP CLK t 23.8 ...

Page 10

... Timing Chart a. Horizontal Timing Chart DCLK DATA Invalid Data (R,G,B) t HFP DENA HD b. Vertical Timing Chart HD LINE DATA DENA VD T-51944D104J-FW-A-AA (AA) No. 2004-0189 First Data HBP HA t WHL Invalid Data t t VFP VBP t WVL OPTREX CORPORATION 799 800 Invalid Data Last Data ...

Page 11

... MAGENTA 1 YELLOW 1 WHITE 1 RED(1) 0 RED(2) 0 RED RED(62) 1 RED(63) 1 GREEN(1) 0 GREEN(2) 0 GREEN GREEN(62) 0 GREEN(63) 0 BLUE(1) 0 BLUE(2) 0 BLUE BLUE(62) 0 BLUE(63) 0 [Note] 1) Definition of gray scale Color (n) --- n indicates gray scale level. Higher n means brighter level. 2) Data 1:High, 0: Low T-51944D104J-FW-A-AA (AA) No. 2004-0189 R DATA LSB MSB ...

Page 12

... MAGENTA YELLOW WHITE RED( RED(2) RED RED(255 GREEN( GREEN(2) GREEN GREEN(255 BLUE( BLUE(2) BLUE BLUE(255) [Note] 1) Definition of gray scale Color (n) --- n indicates gray scale level. Higher n means brighter level. 2) Data 1:High, 0: Low T-51944D104J-FW-A-AA (AA) No. 2004-0189 INPUT DATA R DATA G DATA LSB MSB ...

Page 13

... Display Position and Scan Direction D(X,Y) shows the data number of input signal for LCD panel signal processing PCB. SC: Low or Open               D(1,1) D(1,600) T-51944D104J-FW-A-AA (AA) No. 2004-0189 SC: High D(800,1) D(800,600) CN2 ...

Page 14

... BLOCK DIAGRAM Timing signal Display data Timing Converter Power Power Supply Circuit BACKLIGHT T-51944D104J-FW-A-AA (AA) No. 2004-0189 CN2, 3 CCFL 1 2 OPTREX CORPORATION G1 G2 TFT-LCD G600 Drivers(source) Page 14/34 ...

Page 15

... MECHANICAL SPECIFICATIONS (1) Front Side T-51944D104J-FW-A-AA (AA) No. 2004-0189 OPTREX CORPORATION (Unit: mm) Page 15/34 ...

Page 16

... Rear Side [Note] We recommend you referring to the detailed drawing for your design. Please contact our company sales representative when you need the detailed drawing. T-51944D104J-FW-A-AA (AA) No. 2004-0189 OPTREX CORPORATION (Unit:mm) Page 16/34 ...

Page 17

... Definition of Contrast Ratio CR=ON (White) Luminance / OFF(Black) Luminance *3) Definition of Luminance Lw= ON (White) Luminance T-51944D104J-FW-A-AA (AA) No. 2004-0189 Ta=25°C, VCC=3.3V, Input Signals: Typ. Values shown in Section 6 SYMBOL CONDITION CR θ = φ = 0° Lw θ = φ = 0° ∆ Lw θ = φ = 0° ...

Page 18

... Continuously display the test pattern shown in the figure below for two-hours. Then display a completely white screen. The previous image shall not persist more than two seconds at 25°C. Rows 298-302 TEST PATTERN FOR IMAGE STICKING TEST T-51944D104J-FW-A-AA (AA) No. 2004-0189 White 90% 10% ...

Page 19

... The judgment of the above tests should be made as follow: Pass: Normal display image, no damage of the display function. (ex. no line defect) Partial transformation of the module parts should be ignored. Fail: No display image, damage of the display function. (ex. line defect) T-51944D104J-FW-A-AA (AA) No. 2004-0189 40°C, 90%RH, 240 h BETWEEN -20°C (1h) and 80°C(1h), CONDITIONS ...