T-51750GD065J-FW-AA Optrex America Inc, T-51750GD065J-FW-AA Datasheet - Page 21

• Manufacturer Part Number: T-51750GD065J-FW-AA
• Description: LCD 6.5" TFT MOD 640X480 VGA
• Manufacturer: Optrex America Inc

Specifications of T-51750GD065J-FW-AA

• Display Type: TFT- Thin Film Transistor
• Display Mode: Transmissive
• Viewing Area: 132.50mm L x 99.40mm W
• Backlight: CCFL - White
• Dot Pixels: 640 x 480 (VGA)
• Interface: TTL
• Attached Touch Screen: No
• Diagonal: 165.1 mm
• Viewing Area (w X H): 132.5 mm x 99.4 mm
• Pixel Density: 640 x 480
• Module Size (w X H X T): 158 mm x 120.4 mm x 11.6 mm
• Backlighting: CCFL White
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• For Use With: TK065V01 - TOOLKIT TFT 6.5" VGA
• Dot Size: -
• Dot Pitch: -
• Lead Free Status / Rohs Status: No RoHS Version Available
• Other names: 73-1243

10. Precautions Relating Product Handling
T-51750GD065J-FW-AA (AA) No. 2003-0199
The Following precautions will guide you in handling our product correctly.
1) Liquid crystal display devices
2) Care of the liquid crystal display module against static electricity discharge.
3) When the LCD module alone must be stored for long periods of time:
4) Use the module with a power supply that is equipped with an overcurrent protector
5) Do not ingest the LCD fluid itself should it leak out of a damaged LCD module. Should
6) Conductivity is not guaranteed for models that use metal holders where solder
7) For models which use CFL:
8) For models which use touch panels:
9) For models which use COG,TAB,or COF:
1. The liquid crystal display device panel used in the liquid crystal display module is
2. The polarizer adhering to the surface of the LCD is made of a soft material.
1. When working with the module, be sure to ground your body and any electrical
2. Avoid the use of work clothing made of synthetic fibers. We recommend cotton
3. Slowly and carefully remove the protective film from the LCD module, since this
1. Protect the modules from high temperature and humidity.
2. Keep the modules out of direct sunlight or direct exposure to ultraviolet rays.
3. Protect the modules from excessive external forces.
1. High voltage of 1000V or greater is applied to the CFL cable connector area.
2. Protect CFL cables from rubbing against the unit and thus causing the wire jacket to
3. The use of CFLs for extended periods of time at low temperatures will significantly
1. Do not stack up modules since they can be damaged by components on neighboring modules.
2. Do not place heavy objects on top of the product. This could cause glass breakage.
1. The mechanical strength of the product is low since the IC chip faces out unprotected
2. Given the fact that the rear of the IC chip is left exposed, in order to protect the unit
made of plate glass. Avoid any strong mechanical shock. Should the glass break
handle it with care.
equipment you may be using. We strongly recommend the use of anti static mats
( made of rubber ), to protect work tables against the hazards of electrical shock.
clothing or other conductivity-treated fibers.
operation can generate static electricity.
circuit,since the module is not provided with this protective feature.
hands or clothing come in contact with LCD fluid, wash immediately with soap.
connections between the metal holder and the PCB are not used. Please contact us
to discuss appropriate ways to assure conductivity.
Care should be taken not to touch connection areas to avoid burns.
become worn.
shorten their service life.
from the rear. Be sure to protect the rear of the IC chip from external forces.
from electrical damage, avoid installation configurations in which the rear of the IC
chip runs the risk of making any electrical contact.
Guard against scratching it.
OPTREX CORPORATION
Page 23/24