NHD-16032AZ-NSW-BBW Newhaven Display, NHD-16032AZ-NSW-BBW Datasheet - Page 23

• Manufacturer Part Number: NHD-16032AZ-NSW-BBW
• Description: LCD MOD GRAPH 160X32 WHI TRANSM
• Manufacturer: Newhaven Display

Specifications of NHD-16032AZ-NSW-BBW

• Display Type: LCD - Monochrome
• Display Mode: Transmissive
• Viewing Area: 64.50mm L x 16.40mm W
• Backlight: LED - White
• Dot Size: 0.49mm W x 0.49mm H
• Dot Pitch: 0.54mm x 0.54mm
• Dot Pixels: 160 x 32
• Interface: Parallel/Serial
• Pixel Density: 160 x 32
• Fluid Type: STN Negative
• Module Size (w X H X T): 114 mm x 44 mm x 13.5 mm
• Backlighting: LED White
• Operating Temperature Range: - 20 C to + 70 C
• Product: Graphic LCD Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

NHD-16032AZ-NSW-BBW
Soldering Precautions:
Operation Precautions:
direct sunlight.
Limited Warranty
Newhaven Displays and modules are not consumer products, but may be incorporated by Newhaven
Display’s customers into consumer products or components thereof, Newhaven Display does not warrant
that its LCDs and components are fit for any such particular purpose.
1.
2.
3.
1. The viewing angle can be adjusted by varying the LCD driving voltage Vo.
2. Since applied DC voltage causes electro-chemical reactions, which deteriorate the display, the applied
3. Driving voltage should be kept within specified range; excess voltage will shorten display life.
4. Response time increases with decrease in temperature.
5. Display color may be affected at temperatures above its operational range.
6.Keep the temperature within the specified range usage and storage. Excessive temperature and humidity
7. For long-term storage over 40 C is required, the relative humidity should be kept below 60%,and avoid
below. Newhaven Display will not be responsible for any subsequent or consequential events or injury
or damage to any personnel or user including third party personnel and/or user. Unless otherwise
agreed in writing between Newhaven Display and the customer, Newhaven Display will only replace or
repair any of its LCD which is found defective electrically or visually when inspected in accordance
with Newhaven Display general LCD inspection standard . (Copies available on request)
has been disregarded. Broken glass, scratches on polarizer mechanical damages as well as defects that
are caused accelerated environment tests are excluded from warranty.
the failures or defect.
pulse waveform should be a symmetric waveform such that no DC component remains. Be sure to use
the specified operating voltage.
could cause polarization degradation, polarizer peel-off or generate bubbles.
4. The modules should be kept in anti-static bags or other containers resistant to static for storage.
5. Only properly grounded soldering irons should be used.
6. If an electric screwdriver is used, it should be grounded and shielded to prevent sparks.
7. The normal static prevention measures should be observed for work clothes and working
8. Since dry air is inductive to static, a relative humidity of 50-60% is recommended.
The liability of Newhaven Display is limited to repair or replacement on the terms set forth
No warranty can be granted if any of the precautions state in handling liquid crystal display above
In returning the LCD/LCM, they must be properly packaged; there should be detailed description of
defective insulation of terminals.
benches.
1. Soldering should be performed only on the I/O terminals.
2. Use soldering irons with proper grounding and no leakage.
3. Soldering temperature: 280qC+10qC
4. Soldering time: 3 to 4 second.
5. Use eutectic solder with resin flux filling.
6. If flux is used, the LCD surface should be protected to avoid spattering flux.
7. Flux residue should be removed.
23 / 23
NEWHAVEN DISPLAY