DMC-20261NYJ-LY-BCE Optrex America Inc, DMC-20261NYJ-LY-BCE Datasheet - Page 6
![LCD MODULE 20X2 CHARACTER](/photos/15/62/156206/c-51850nfqj-lw-aan_sml.jpg)
DMC-20261NYJ-LY-BCE
Manufacturer Part Number
DMC-20261NYJ-LY-BCE
Description
LCD MODULE 20X2 CHARACTER
Manufacturer
Optrex America Inc
Series
DMC-20261r
Specifications of DMC-20261NYJ-LY-BCE
Display Type
STN - Super-Twisted Nematic
Display Mode
Transmissive
Number Of Digits/alpha
40
Outline L X W X H
116.00mm x 37.00mm x 15.70mm
Viewing Area
83.00mm L x 18.60mm W
Backlight
LED - Yellow
Display Format
20 x 2
Character Size
5.55mm H x 3.20mm W
Character Format
5 x 8 Dots
Voltage - Supply
+5 V, -7 V
Dot Size
0.60mm W x 0.65mm H
Interface
Parallel
Operating Temperature
-20°C ~ 70°C
Lead Free Status / Rohs Status
No
Other names
73-1063
DMC-20261NYJ-LY-D
OP220NYJLY-D
DMC-20261NYJ-LY-D
OP220NYJLY-D
Recommended
Contrast Ratio
Viewing Angle
Response
DMC20261NYJ-LY-BCE (CD) No.99-0207
3.Optical Specif ications
Note 1 :
Note 1 : Contrast ratio is definded as follows.
Note 2 : The time that the luminance level reaches 90% of the saturation level from 0% when ON
Note 3 : The time that the luminance level reaches 10% of the saturation level from 100% when OFF
Note 4 : Definition of Driving Voltage V
3.1.LCD Driving Voltage
3.2.Optical Characteristics
LCD Driving Voltage
Time
Parameter
Parameter
minimum and maximum shows tolerance of the operating voltage. The specified contrast ratio and
response time are not guaranteed over the entire range.
L
L
signal is applied.
signal is applied.
Assuming that the typical driving waveforms shown below are applied to the LCD Panel at
1/A Duty - 1/B Bias ( A : Duty Number, B : Bias Number ). Driving voltage V
as follows.
Vth1 : The voltage V
Vth2 : The voltage V
ON
OFF
CR = L
V
Rise
Decay Note 3
Voltage (Applied actual waveform to LCD Module) for the best contrast. The range of
: Luminance of the ON segments
: Luminance of the OFF segments
D
V
the segment which the ON signal is applied to.
the segment which the OFF signal is applied to.
= (Vth1+Vth2) / 2
O-P
Note 1
Note 1
OFF
Note 2
1 / (
〈 ON SIGNAL 〉
/ L
ON
f
F
× A )
O-P
O-P
V
Symbol
Symbol
DD
T
T
that should provide 50% of the saturation level in the luminance at
that should provide 50% of the saturation level in the luminance at
CR
OFF
ON
-V
EE
Ta=25℃, 1/16 Duty, 1/5 Bias, V
D
θ= 0 ゚, φ=-゚
Conditions
Conditions
Ta= -20℃
Ta=25℃
Ta=70℃
-
-
OPTREX
OPTREX CORPORATION
1 /
〈 OFF SIGNAL 〉
f
F
Shown in 3.3
Min.
Min.
7.2
6.3
-
-
-
-
D
=7.7V (Note 4), θ= 0 ゚, φ=-゚
( B-2 ) × V
Typ.
Typ.
7.7
-
-
60
90
5
O-P
D
Max.
Max.
is definded
/ B
120
180
8.9
8.2
-
-
Page 6/16
Units
Units
ms
ms
V
V
V