NHD-0216HZ-FSW-FBW-3V3C Newhaven Display, NHD-0216HZ-FSW-FBW-3V3C Datasheet
NHD-0216HZ-FSW-FBW-3V3C
Specifications of NHD-0216HZ-FSW-FBW-3V3C
Related parts for NHD-0216HZ-FSW-FBW-3V3C
NHD-0216HZ-FSW-FBW-3V3C Summary of contents
Page 1
... User’s Guide NHD-0216HZ-FSW-FBW-3V3C LCM (Liquid Crystal Display Module) RoHS Compliant Newhaven Display NHD- 2 Lines x 16 Characters 0216- Version Line HZ- Transflective F- Side White LED B/L SW- FSTN positive F- 6:00 View B- Wide Temperature (-20 ~ +70c) W- +3.3V power supply with temperature compensation 3V3- Built-in controller (SPLC780D or equivalent) ...
Page 2
... NHD-0216HZ-FSW-FBW-3V3C DOCUMENT REVISION HISTORY VERSINO DATE 00 NOV-18-2008 CONTENTS Item Functions & Features Mechanical specifications Dimensional Outline Absolute maximum ratings Block diagram Pin description Contrast adjust Optical characteristics Electrical characteristics Timing Characteristics Instruction description Display character address code: character pattern Quality Specifications ...
Page 3
... NHD-0216HZ-FSW-FBW-3V3C 1.Features 1. 5x8 dots with cursor 2. Built-in controller (SPLC780D or equivalent) 3. +3.3V power supply with temperature compensation 4. 1/16 duty cycle;1/5bias 5. BKL to be driven by pin15, pin16 6. 16characters *2lines display ;FSTN positive LCD type †STN Yellow Green ;6 O’clock View direction †Reflective Rear Polarizer ...
Page 4
...
Page 5
Item Power voltage Input voltage Operating temperature range Storage temperature range 5.Block diagram 6.Interface pin description Pin no. Symbol connection 1 GND 2 VDD Power supply R 7~10 DB0~DB3 11~14 ...
Page 6
... NHD-0216HZ-FSW-FBW-3V3C 7.Contrast adjust V : LCD Driving voltage V DD~ 0 VR: 10k~20k 7. Optical characteristics TN type display module (Ta=25℃, VDD=3.0V) Item Symbol Viewing angle Contrast ratio Response time (rise) Response time (fall) STN type display module (Ta=25℃, VDD=3.0V) Item Symbol Viewing angle Contrast ratio ...
Page 7
... NHD-0216HZ-FSW-FBW-3V3C 9. Timing Characteristics Write cycle (Ta=25℃, VDD=3.0V) Parameter Symbol Enable cycle time t c Enable pulse width t w Enable rise/fall time RS; R/W setup time t su1 RS; R/W address hold t h1 time Read data output delay t su2 Read data hold time t h2 Write mode timing diagram ...
Page 8
... NHD-0216HZ-FSW-FBW-3V3C Read cycle (Ta=25℃, VDD=3.0V) Parameter Symbol Enable cycle time t c Enable pulse width t w Enable rise/fall time RS; R/W setup time t su RS; R/W address hold t h time Read data output delay t d Read data hold time t dh Read mode timing diagram ...
Page 9
... NHD-0216HZ-FSW-FBW-3V3C 11.Instruction description 11.1Outline To overcome the speed difference between the internal clock of KS0066U and the MPU clock, KS0066U performs internal operations by storing control in formations DR. The internal operation is determined according to the signal from MPU, composed of read/write and data bus (Refer to Table7). Instructions can be divided largely into four groups: 1) KS0066U function set instructions (set display methods, set data length, etc ...
Page 10
... NHD-0216HZ-FSW-FBW-3V3C to “Low”. 11.3Contents 1) Clear display RS R/W DB7 Clear all the display data by writing “20H” (space code) to all DDRAM address, and set DDRAM address to “00H” into AC (address counter). Return cursor to the original status, namely, bring the cursor to the left edge on the fist line of the display. ...
Page 11
... NHD-0216HZ-FSW-FBW-3V3C Note that display shift is performed simultaneously in all the lines. When display data is shifted repeatedly, each line is shifted individually. When display shift is performed, the contents of the address counter are not changed. Shift patterns according to S/C and R/L bits S/C R Shift cursor to the left decreased by 1 ...
Page 12
... NHD-0216HZ-FSW-FBW-3V3C Write binary 8-bit data to DDRAM/CGRAM. The selection of RAM from DDRAM, and CGRAM, is set by the previous address set instruction (DDRAM address set, CGRAM address set). RAM set instruction can also determine the AC direction to RAM. After write operation. The address is automatically increased/decreased by 1, according to the entry mode. ...
Page 13
... NHD-0216HZ-FSW-FBW-3V3C 13.Standard character pattern Newhaven Display ...
Page 14
... NHD-0216HZ-FSW-FBW-3V3C 14.QUALITY SPECIFICATIONS 14.1 Standard of the product appearance test Manner of appearance test: The inspection should be performed in using 20W x 2 fluorescent lamps. Distance between LCM and fluorescent lamps should be 100 cm or more. Distance between LCM and inspector eyes should more. Viewing direction for inspection is 45° from vertical against LCM. ...
Page 15
... NHD-0216HZ-FSW-FBW-3V3C 14.2 Specification of quality assurance AQL inspection standard Sampling method: MIL-STD-105E, Level II, single sampling Defect classification (Note not including) Classify Major Display state Non-display Minor Display state Polarizer Soldering Wire TAB Item Short or open circuit LC leakage Flickering No display Wrong viewing direction ...
Page 16
... NHD-0216HZ-FSW-FBW-3V3C Note on defect classification No. Item 1 Short or open circuit LC leakage Flickering No display Wrong viewing direction Wrong Back-light 2 Contrast defect Background color deviation 3 Point defect, Black spot, dust (including Polarizer (X+Y)/2 Line defect, 4 Scratch 5 Rainbow Criterion Not allow Refer to approval sample Point Y Size I 0 ...
Page 17
... NHD-0216HZ-FSW-FBW-3V3C No Item 6 Chip Remark: X: Length direction Y: Short direction Z: Thickness direction t: Glass thickness W: Terminal Width Y W Criterion Acceptable criterion X Y ≤ Acceptable criterion X Y ≤2 Z Acceptable criterion shall not reach to ITO X Acceptable criterion Y Disregard Z X Acceptable criterion Y ≤ Newhaven Display 0.5mm ≤t/2 ...
Page 18
... NHD-0216HZ-FSW-FBW-3V3C No. Item 7 Segment pattern W = Segment width I = (X+Y)/2 8 Back-light 9 Soldering 10 Wire 11* PCB Criterion (1) Pin hole I < 0.10mm is acceptable Point Size I≤1/ I≤1/2W 1/4W I＞1/2W W (1) The color of backlight should correspond its specification. (2) Not allow flickering (1) Not allow heavy dirty and solder ball on PCB. ...
Page 19
... NHD-0216HZ-FSW-FBW-3V3C No Item 12 Protruded W: Terminal Width 13 TAB 1. Position 2 TAB bonding strength test 14 Total no. of acceptable A. Zone Defect B. Zone Criterion TAB P (=F/TAB bonding width) ≥650gf/cm ,(speed rate: 1mm/min) 5pcs per SOA (shipment) Maximum 2 minor non-conformities per one unit. Defect distance: each point to be separated over 10mm It is acceptable when trouble for quality and assembly in customer’ ...
Page 20
... NHD-0216HZ-FSW-FBW-3V3C 14.3 Reliability of LCM Reliability test condition: Item High temp. Storage High temp. Operating Low temp. Storage Low temp. Operating Humidity Temp. Cycle Recovery time should be 24 hours minimum. Moreover, functions, performance and appearance shall be free from remarkable deterioration within 50,000 hours under ordinary operating and storage conditions room temperature (20+8qC), normal humidity (below 65% RH), and in the area not exposed to direct sun light ...
Page 21
... NHD-0216HZ-FSW-FBW-3V3C defective insulation of terminals. 4. The modules should be kept in anti-static bags or other containers resistant to static for storage. 5. Only properly grounded soldering irons should be used electric screwdriver is used, it should be grounded and shielded to prevent sparks. 7. The normal static prevention measures should be observed for work clothes and working benches ...