900-00005 Parallax Inc, 900-00005 Datasheet

900-00005

Manufacturer Part Number

900-00005

Description

SERVO PARALLAX STANDARD

Manufacturer

Parallax Inc

Type

DC Servor

Datasheet

1.900-00005.pdf (4 pages)

Specifications of 900-00005

Voltage - Rated

6VDC

Product

Microcontroller Accessories

For Use With

28824 - SERVOPAL SERVO PULSER TIMER

Features

Rpm

Shaft Diameter

Shaft Rotational Direction

Lead Free Status / Rohs Status

Lead free / RoHS Compliant

Current page: 1 of 4
Download datasheet (87Kb)

Parallax Standard Servo (#900-00005)

The Parallax Standard Servo is ideal for robotics and basic movement projects.

Features

Technical Specifications

*Power Requirement Notes

Futaba specifies 4-6 VDC for this servo. However, we find that this servo is tolerant of a 9 V battery for

short periods of time when there is no load, as used in some activities in the Stamps in Class series of

tutorials. (Slight jittering may be observed when batteries are fresh; this does not cause damage). Do

not use this servo with an unregulated wall-mount supply, or a regulated wall mount supply exceeding 6

VDC.

Servo current draw can spike while under load. Be sure that your application's power supply and voltage

regulator is prepared to supply adequate current for all servos used. Do not try to power this servo

directly from a BASIC Stamp module's Vdd or Vin pins; do not connect the servo's Vss line directly to the

BASIC Stamp module's Vss pin.

Holds any position between 0 and 180 degrees

43.1 oz-in torque at 6 V

Accepts four mounting screws

Easy to interface with any Parallax microcontroller

High precision gear made of the POM (polyacetal)

resin makes the operation smooth causing no

backlash.

Manufactured for Parallax exclusively by Futaba

Power requirements: 4 to 6 VDC* (see Power Requirement Notes below)

Maximum current draw: 140 +/- 50 mA at 6 VDC when operating in no load conditions

Communication: Pulse-width modulation

Dimensions approx 2.2 x 0.8 x 1.6 in (5.58x 1.9 x 40.6 cm) excluding servo horn

Operating temperature range: 14 to 122°F (-10 to 50°C)

Weight: 1.55 oz (44 g)

15 mA when in static state

Parallax Standard Servo (#900-00005)

Web Site: www.parallax.com

Forums: forums.parallax.com

Sales: sales@parallax.com

Technical: support@parallax.com

Office: (916) 624-8333

Fax: (916) 624-8003

Sales: (888) 512-1024

Tech Support: (888) 997-8267

v2.0 7/9/2009 Page 1 of 4

Related parts for 900-00005

900-00005 Summary of contents

Page 1

... BASIC Stamp module's Vdd or Vin pins; do not connect the servo's Vss line directly to the BASIC Stamp module's Vss pin. Copyright © Parallax Inc. Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Parallax Standard Servo (#900-00005) Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267 v2.0 7/9/2009 Page ...

Page 2

... Vdd as shown in the figure below. Failure to place the jumper at this setting can cause damage your servo Vdd 13 12 Red Black X4 X5 Vin Copyright © Parallax Inc. Standard Servo Description Minimum 3.3 Power Supply 4.0 Ground Product Name (#900-00005) Typical Maximum Units 5.0 Vservo + 0.2 V 5.0 6 v2.0 7/9/2009 Page ...

Page 3

... When adapting BS2 code to another BASIC Stamp model, you may need to make adjustments. The table below lists the PULSOUT ranges for each BASIC Stamp microcontroller. See the BASIC Stamp Manual or BASIC Stamp Editor Help for more information. Copyright © Parallax Inc. Product Name (#900-00005) Duration argument. v2.0 7/9/2009 Page ...

Page 4

... Duration (ms) Duration units (µs) ' System clock → 80 MHz ' Configure Counter A to NCO ' Mark counter time ' Repeat PWM signal ' Set up the pulse ' Calculate next cycle repeat ' Wait for next cycle Product Name (#900-00005) 1.7 ms 200 1000 2500 v2.0 7/9/2009 Page ...

Related keywords

900-00005 datasheet
900-00005 data sheet
900-00005 pdf datasheet
900-00005 component
900-00005 part
900-00005 distributor
900-00005 RoHS
900-00005 datasheet download