MT18LSDT6472AY-13ED2 Micron Technology Inc, MT18LSDT6472AY-13ED2 Datasheet
MT18LSDT6472AY-13ED2
Specifications of MT18LSDT6472AY-13ED2
Related parts for MT18LSDT6472AY-13ED2
MT18LSDT6472AY-13ED2 Summary of contents
Page 1
... PRODUCTS AND SPECIFICATIONS DISCUSSED HEREIN ARE SUBJECT TO CHANGE BY MICRON WITHOUT NOTICE. 256MB (x72, ECC, SR), 512MB (x72, ECC, DR) MT9LSDT3272(L)A(I) – 256MB MT18LSDT6472(L)A(I) – 512MB For the latest data sheet, please refer to the Micron site: www.micron.com/products/modules Figure 1: 168-Pin DIMM (MO–161) Standard 1.375in./34.93mm Low Profile 1.125in./28.58mm Options • Operating Temperature Range Commercial (0° ...
Page 2
Table 3: Part Numbers PART NUMBER MT9LSDT3272(L)AG-13E_ MT9LSDT3272(L)AY-13E_ MT9LSDT3272(L)A(I)G-133_ MT9LSDT3272(L)A(I)Y-133_ MT9LSDT3272(L)AG-10E_ MT9LSDT3272(L)AY-10E_ MT18LSDT6472(L)AG-13E_ MT18LSDT6472(L)AY-13E_ MT18LSDT6472(L)A(I)G-133_ MT18LSDT6472(L)A(I)Y-133_ MT18LSDT6472(L)AG-10E_ MT18LSDT6472(L)AY-10E_ NOTE: Designators for component and PCB revision are the last two characters of each part number Consult factory for current revision codes. ...
Page 3
Table 4: Pin Assignment (168-Pin DIMM Front) PIN SYMBOL PIN SYMBOL PIN SYMBOL PIN SYMBOL CB1 DQ0 DQ1 DQ2 DQ3 26 ...
Page 4
Table 6: Pin Descriptions Pin numbers may not correlate with symbols; refer to the Pin Assignment tables on page 3 for more information PIN NUMBERS 27, 111, 115 42, 79, 125, 163 63, 128 30, 45,114, 129 28, 29, 46, ...
Page 5
Table 6: Pin Descriptions Pin numbers may not correlate with symbols; refer to the Pin Assignment tables on page 3 for more information PIN NUMBERS 6, 18, 26, 40, 41, 49, 59, 73, 84, 90, 102, 110, 124, 133, 143, ...
Page 6
... CKE0 WE# A0-A12 BA0 BA1 Note: 1. All resistor values are 10 unless otherwise specified. 2. Per industry standard, Micron modules use various component speed grades as referenced in the module part numbering guide at support/numbering.html. 09005aef807b3709 SD9_18C32_64X72AG.fm - Rev. E 11/04 EN 256MB (x72, ECC, SR), 512MB (x72, ECC, DR) DQMB0 DQMB4 ...
Page 7
... A0-A12 BA0 BA1 Note: 1. All resistor values are 10 unless otherwise specified. 2. Per industry standard, Micron modules use various component speed grades as referenced in the module part numbering guide at support/numbering.html. 09005aef807b3709 SD9_18C32_64X72AG.fm - Rev. E 11/04 EN 256MB (x72, ECC, SR), 512MB (x72, ECC, DR) S1# DQMB4 CS# ...
Page 8
... SDRAM devices with a synchronous interface (all signals are registered on the positive edge of the clock signals). Read and write accesses to the SDRAM modules are burst oriented; accesses start at a selected location and continue for a programmed number of locations in a programmed sequence. Accesses begin with the regis- tration of an ACTIVE command, which is then followed by a READ or WRITE command ...
Page 9
M10 and M11 are reserved for future use. Address A12 (M12) is undefined but should be driven LOW during loading of the mode register. The mode register must be loaded when all device banks are idle, and ...
Page 10
Table 7: Burst Definition Table STARTING BURST COLUMN ORDER OF ACCESSES WITHIN LENGTH ADDRESS TYPE = SEQUENTIAL 0 0-1-2 1-2-3 2-3-0 3-0-1 ...
Page 11
Test modes and reserved states should not be used because unknown operation or incompatibility with future versions may result. Write Burst Mode When the burst length programmed via M0- M2 applies to both READ and WRITE bursts; ...
Page 12
Commands The Truth Table, below, provides a quick reference of available commands. This is followed by written description of each command. For a more detailed Table 9: SDRAM Commands and DQMB Operation Truth Table CKE is HIGH for all commands ...
Page 13
Absolute Maximum Ratings Stresses greater than those listed may cause perma- nent damage to the device. This is a stress rating only, and functional operation of the device at these or any other conditions above those indicated in the opera- ...
Page 14
Table 12: I Specifications and Conditions – 256MB DD Notes 11, 13; notes appear on page 18; V PARAMETER/CONDITION OPERATING CURRENT: Active Mode; Burst = 2; READ or WRITE (MIN) STANDBY CURRENT: ...
Page 15
Table 14: Capacitance – 256MB . Note 2; notes appear on page 18 PARAMETER Input Capacitance: Address and Command Input Capacitance: CK0 Input Capacitance: CK2 Input Capacitance: S0# Input Capacitance: S2# Input Capacitance: CKE Input Capacitance: DQMB0, 2– ...
Page 16
Table 16: Electrical Characteristics and Recommended AC Operating Conditions Notes 11, 31; notes appear on page 18 Module AC timing parameters comply with PC100 and PC133 Design Specs, based on component parameters ACCHARACTERISTICS PARAMETER Access timefrom ...
Page 17
Table 17: AC Functional Characteristics Notes 11, 31; notes appear on page 18 PARAMETER READ/WRITE command to READ/WRITE command CKE to clock disable or power-down entry mode CKE to clock enable or power-down exit setup ...
Page 18
Notes 1. All voltages referenced This parameter is sampled MHz 25°C; pin under test biased at 1.4V dependent on output loading and cycle DD rates. Specified values are ...
Page 19
SPD Clock and Data Conventions Data states on the SDA line can change only during SCL LOW. SDA state changes during SCL HIGH are reserved for indicating start and stop conditions (as shown in Figure 7, Data Validity, and Figure ...
Page 20
Table 18: EEPROM Device Select Code The most significant bit (b7) is sent first Memory Area Select Code (two arrays) Protection Register Select Code Table 19: EEPROM Operating Modes MODE RW BIT Current Address Read RandomAddressRead Sequential Read Byte Write ...
Page 21
Table 20: Serial Presence-Detect EEPROM DC Operating Conditions All voltages referenced DDSPD PARAMETER/CONDITION SUPPLY VOLTAGE INPUT HIGH VOLTAGE: Logic 1; All inputs INPUT LOW VOLTAGE: Logic 0; All inputs OUTPUT LOW VOLTAGE 3mA ...
Page 22
Table 22: Serial Presence-Detect Matrix “1”/”0”: Serial data, “driven to HIGH”/”driven to LOW”; V BYTE DESCRIPTION 0 Number of Bytes Used by Micron 1 Total Number of SPD Memory Bytes 2 Memory Type 3 Number of Row Addresses 4 Number ...
Page 23
... Module Serial Number 99-125 Manufacturer-Specific Data (RSVD) 126 System Frequency 127 SDRAM Component & Clock Detail NOTE The value of RAS used for -13E modules is calculated from 09005aef807b3709 SD9_18C32_64X72AG.fm - Rev. E 11/04 EN 256MB (x72, ECC, SR), 512MB (x72, ECC, DR) = +3.3V ±0.3V DD ENTRY (VERSION) 256MB ...
Page 24
Figure 11: 168-Pin DIMM Dimensions – 256MB U1 U2 0.079 (2.00) R (2X) 0.118 (3.00) (2X) 0.118 (3.00) TYP 0.250 (6.35) TYP 0.118 (3.00) TYP 2.625 (66.68) PIN 1 (PIN 85 ON BACKSIDE) 0.079 (2.00) R (2X 0.118 ...
Page 25
Figure 12: 168-Pin DIMM Dimensions – 512MB U1 0.079 (2.00) R (2X) 0.118 (3.00) (2X) 0.118 (3.00) TYP 0.118 (3.00) TYP PIN 1 U11 PIN 168 0.079 (2.00) R (2X 0.118 (3.00) (2X) 0.118 (3.00) TYP 0.118 (3.00) ...
Page 26
Data Sheet Designation Released (No Mark): This data sheet contains mini- mum and maximum limits specified over the complete power supply and temperature range for production 8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-3900 E-mail: prodmktg@micron.com, ...