MT9HTF6472AY-80ED4 Micron Technology Inc, MT9HTF6472AY-80ED4 Datasheet
MT9HTF6472AY-80ED4
Specifications of MT9HTF6472AY-80ED4
Related parts for MT9HTF6472AY-80ED4
MT9HTF6472AY-80ED4 Summary of contents
Page 1
... DDR2 SDRAM UDIMM MT9HTF3272AY – 256MB MT9HTF6472AY – 512MB MT9HTF12872AY – 1GB Features • 240-pin, unbuffered dual in-line memory module • Fast data transfer rates: PC2-3200, PC2-4200, PC2-5300, or PC2-6400 • 256MB (32 Meg x 72), 512MB (64 Meg x 72), or 1GB (128 Meg x 72) • ...
Page 2
Table 2: Addressing Parameter Refresh count Row address Device bank address Device configuration Column address Module rank address Table 3: Part Numbers and Timing Parameters – 256MB 1 Base device: MT47H32M8, 256Mb DDR2 SDRAM Module 2 Part Number Density MT9HTF3272A(I)Y-667__ ...
Page 3
... The data sheet for the base device can be found on Micron’s Web site. Notes: 2. All part numbers end with a two-place code (not shown) that designates component and PCB revisions. Consult factory for current revision codes. Example: MT9HTF6472AY-667C2. PDF: 09005aef80e8ad4d htf9c32_64_128x72ay – Rev. F 3/10 EN ...
Page 4
Pin Assignments Table 6: Pin Assignments 240-Pin UDIMM Front Pin Symbol Pin Symbol Pin DQ19 61 REF DQ0 33 DQ24 63 4 DQ1 34 DQ25 ...
Page 5
... Pin Descriptions The pin description table below is a comprehensive list of all possible pins for all DDR2 modules. All pins listed may not be supported on this module. See Pin Assignments for information specific to this module. Table 7: Pin Descriptions Symbol Type Ax Input BAx Input ...
Page 6
Table 7: Pin Descriptions (Continued) Symbol Type SDA I/O RDQSx, Output RDQS#x Err_Out# Output (open drain Supply DD DDQ V Supply DDSPD V Supply REF V Supply SS – NC – NF – NU – RFU PDF: 09005aef80e8ad4d ...
Page 7
Functional Block Diagram Figure 2: Functional Block Diagram S0# DQS0# DQS0 DM0 DQS1# DQS1 DM1 DQS2# DQS2 DM2 DQS3# DQS3 DM3 DQS8# DQS8 DM8 BA[2/1:0] A[13/12:0] PDF: 09005aef80e8ad4d htf9c32_64_128x72ay – Rev. F 3/10 EN 256MB, 512MB, 1GB (x72, SR, ECC) ...
Page 8
... Pin Descriptions The pin description table below is a comprehensive list of all possible pins for all DDR2 modules. All pins listed may not be supported on this module. See Pin Assignments for information specific to this module. Table 8: Pin Descriptions Symbol Type Ax Input BAx Input ...
Page 9
Table 8: Pin Descriptions (Continued) Symbol Type SDA I/O RDQSx, Output RDQS#x Err_Out# Output (open drain Supply DD DDQ V Supply DDSPD V Supply REF V Supply SS – NC – NF – NU – RFU PDF: 09005aef80e8ad4d ...
Page 10
... DRAM core and eight corresponding n-bit-wide, one-half-clock-cycle data trans- fers at the I/O pins. DDR2 modules use two sets of differential signals: DQS, DQS# to capture data and CK and CK# to capture commands, addresses, and control signals. Differential clocks and data strobes ensure exceptional noise immunity for these signals and provide precise crossing points to capture input signals ...
Page 11
Electrical Specifications Stresses greater than those listed may cause permanent damage to the module. This is a stress rating only, and functional operation of the module at these or any other condi- tions outside those indicated in the device data ...
Page 12
... Design Considerations Simulations Micron memory modules are designed to optimize signal integrity through carefully de- signed terminations, controlled board impedances, routing topologies, trace length matching, and decoupling. However, good signal integrity starts at the system level. Mi- cron encourages designers to simulate the signal characteristics of the system's memo- ry bus to ensure adequate signal integrity of the entire memory system ...
Page 13
I Specifications DD Table 11: DDR2 I Specifications and Conditions – 256MB DD Values shown for MT47H32M8 DDR2 SDRAM only and are computed from values specified in the 256Mb (32 Meg x 8) component data sheet Parameter Operating one bank ...
Page 14
Table 12: DDR2 I Specifications and Conditions – 512MB DD Values shown for MT47H64M8 DDR2 SDRAM only and are computed from values specified in the 512Mb (64 Meg x 8) component data sheet Parameter Operating one bank active-precharge current: t ...
Page 15
Table 12: DDR2 I Specifications and Conditions – 512MB (Continued) DD Values shown for MT47H64M8 DDR2 SDRAM only and are computed from values specified in the 512Mb (64 Meg x 8) component data sheet Parameter Operating bank interleave read current: ...
Page 16
Table 13: DDR2 I Specifications and Conditions (Die Revision A) – 1GB DD Values shown for MT47H128M8 DDR2 SDRAM only and are computed from values specified in the 1Gb (128 Meg x 8) com- ponent data sheet Parameter Operating one ...
Page 17
Table 13: DDR2 I Specifications and Conditions (Die Revision A) – 1GB (Continued) DD Values shown for MT47H128M8 DDR2 SDRAM only and are computed from values specified in the 1Gb (128 Meg x 8) com- ponent data sheet Parameter Operating ...
Page 18
Table 14: DDR2 I Specifications and Conditions (Die Revision E) – 1GB DD Values shown for MT47H128M8 DDR2 SDRAM only and are computed from values specified in the 1Gb (128 Meg x 8) com- ponent data sheet Parameter Operating one ...
Page 19
Table 14: DDR2 I Specifications and Conditions (Die Revision E) – 1GB (Continued) DD Values shown for MT47H128M8 DDR2 SDRAM only and are computed from values specified in the 1Gb (128 Meg x 8) com- ponent data sheet Parameter Operating ...
Page 20
Serial Presence-Detect For the latest SPD data, refer to Micron's SPD page: www.micron.com/SPD. Table 15: SPD EEPROM Operating Conditions Parameter/Condition Supply voltage Input high voltage: logic 1; All inputs Input low voltage: logic 0; All inputs Output low voltage: I ...
Page 21
Module Dimensions Figure 3: 240-Pin DDR2 UDIMM 2.00 (0.079) R (4X 2.50 (0.098) D (2X) 2.30 (0.091) TYP Pin 1 2.21 (0.087) TYP 1.0 (0.039) TYP 1.0 (0.039) TYP 70.66 (2.782) No components this side of module 3.04 ...