MT18HTF25672FDY-53EA5E3 Micron Technology Inc, MT18HTF25672FDY-53EA5E3 Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/4/441/micron_technology_inc_sml.jpg)
MT18HTF25672FDY-53EA5E3
Manufacturer Part Number
MT18HTF25672FDY-53EA5E3
Description
MODULE DDR2 2GB 240FBDIMM
Manufacturer
Micron Technology Inc
Datasheet
1.MT18HTF12872FDY-53EB5E3.pdf
(12 pages)
Specifications of MT18HTF25672FDY-53EA5E3
Memory Type
DDR2 SDRAM
Memory Size
2GB
Speed
533MT/s
Package / Case
240-FBDIMM
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
General Description
Advanced Memory Buffer
I
Table 7: I
PDF: 09005aef81a2f237
htf18c128_256x72fdy.pdf - Rev. D 12/09 EN
Symbol
I
I
I
I
DD
DD_IDLE_0
DD_IDLE_1
DD_ACTIVE_1
DD_ACTIVE_2
Conditions and Specifications
DD
Conditions
Micron’s FBDIMM devices adhere to the currently proposed industry specifications for
FBDIMMs. The following specifications contain detailed information on FBDIMM de-
sign, interfaces, and theory of operation and are listed here for the system designers’
convenience. Refer to the JEDEC Web site for available specifications.
• FBDIMM Design Specification – pending JEDEC approval
• FBDIMM: Architecture and Protocol – JESD206
• FBDIMM: Advanced Memory Buffer (AMB) – JESD82-20
• Design for Test, Design for Validation (DFx) Specification
• Serial Presence-Detect (SPD) for Fully Buffered DIMM – JEDEC Standard No. 21-C,
This DDR2 SDRAM module is a high-bandwidth, large-capacity channel solution that
has a narrow host interface. FBDIMM devices use DDR2 SDRAM devices isolated from
the channel behind an AMB buffer on the FBDIMM. Memory device capacity remains
high, and total memory capacity scales with DDR2 SDRAM bit density.
As shown in the System Block Diagram, the FBDIMM channel provides a communica-
tion path from a host controller to an array of DDR2 SDRAM devices, with the DDR2
SDRAM devices buffered behind an AMB device. The physical isolation of the DDR2
SDRAM devices from the channel enhances the communication path and significantly
increases the reliability and availability of the memory subsystem.
The AMB isolates the DDR2 SDRAM devices from the channel. This single-chip AMB
component, located in the center of each FBDIMM, acts as a repeater and buffer for all
signals and commands exchanged between the host controller and DDR2 SDRAM devi-
ces, including data input and output. The AMB communicates with the host controller
and adjacent FBDIMMs on a system board using an industry-standard, high-speed, dif-
ferential, 1.5V, point-to-point interface. The AMB also enables buffering of memory
traffic to support large memory capacities. Refer to the JEDEC JESD82-20 specification
for further information.
Condition
Idle current, single, or last DIMM: L0 state; Idle (0% bandwidth); Primary channel ena-
bled; Secondary channel disabled; CKE HIGH; Command and address lines stable; DDR2
SDRAM clock active
Idle current, first DIMM: L0 state; Idle (0% bandwidth); Primary and secondary channels
enabled; CKE HIGH; Command and address lines stable; DDR2 SDRAM clock active
Active power: L0 state; 50% DRAM bandwidth; 67% READ; 33% WRITE; Primary and secon-
dary channels enabled; DDR2 SDRAM clock active; CKE HIGH
Active power, data pass through: L0 state; 50% DRAM bandwidth to downstream
DIMM; 67% READ; 33% WRITE; Primary and secondary channels enabled; DDR2 SDRAM
clock active; CKE HIGH; Command and address lines stable
page 4.1.2.7-1
1GB, 2GB (x72, DR) 240-Pin DDR2 SDRAM FBDIMM
7
Micron Technology, Inc. reserves the right to change products or specifications without notice.
General Description
© 2005 Micron Technology, Inc. All rights reserved.