MT5HTF3272PKY-53EB2 Micron Technology Inc, MT5HTF3272PKY-53EB2 Datasheet - Page 4

• Manufacturer Part Number: MT5HTF3272PKY-53EB2
• Description: MODULE DDR2 512MB 244-DIMM
• Manufacturer: Micron Technology Inc

Specifications of MT5HTF3272PKY-53EB2

• Memory Type: DDR2 SDRAM
• Memory Size: 256MB
• Speed: 533MT/s
• Package / Case: 244-DIMM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 5:
PDF: 09005aef818e3e75/Source: 09005aef818e3df5
htf5c32x72k.fm - Rev. B 2/07 EN
RAS#, CAS#, WE#
DQS0#–DQS8#
DQS0–DQS8,
DQ0–DQ63
DM0–DM8
CK0, CK0#
V
BA0, BA1
SA0–SA2
CB0–CB7
Symbol
E
A0–A12
DD
RESET#
P
RR
ODT0
CKE0
SDA
V
AR
S0#
SCL
/V
_O
REF
_I
DD
UT
N
Q
Pin Descriptions
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
Output
Supply
Supply
drain)
(open
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Type
I/O
I/O
I/O
I/O
I/O
On-die termination: ODT (registered HIGH) enables termination resistance internal to the
DDR2 SDRAM. When enabled, ODT is only applied to each of the following pins: DQ, DQS,
DQS#, RDQS, RDQS#, CB, and DM. The ODT input will be ignored if disabled via the LOAD
MODE (LM) command.
Clock: CK and CK# are differential clock inputs. All address and control input signals are
sampled on the crossing of the positive edge of CK and negative edge of CK#. Output data
(DQs and DQS/DQS#) is referenced to the crossings of CK and CK#.
Clock enable: CKE (registered HIGH) activates and CKE (registered LOW) deactivates
clocking circuitry on the DDR2 SDRAM.
Chip select: S# enables (registered LOW) and disables (registered HIGH) the command
decoder. All commands are masked when S# is registered HIGH. S# provides for external
rank selection on systems with multiple ranks. S# is considered part of the command code.
Command inputs: RAS#, CAS#, and WE# (along with S#) define the command being
entered.
Bank address inputs: BA0–BA1 define to which device bank an ACTIVE, READ, WRITE, or
PRECHARGE command is being applied. BA0–BA1 define which mode register, including
MR, EMR, EMR(2), or EMR(3), is loaded during the LM command.
Address inputs: Provide the row address for ACTIVE commands and the column address
and auto precharge bit (A10) for READ/WRITE commands to select one location out of the
memory array in the respective bank. A10 sampled during a PRECHARGE command
determines whether the PRECHARGE applies to one device bank (A10 LOW, device bank
selected by BA0–BA1) or all device banks (A10 HIGH). The address inputs also provide the
op-code during an LM command.
Parity bit for the address and control bus.
Serial clock for presence-detect: SCL is used to synchronize the presence-detect data
transfer to and from the module.
Presence-detect address inputs: These pins are used to configure the presence-detect
device.
Asynchronously forces all registered outputs LOW when RESET# is LOW. This signal can be
used during power-up to ensure that CKE is LOW and DQs are High-Z.
Data input/output: Bidirectional data bus.
Data strobe: Output with read data, input with write data for source synchronous
operation. Edge-aligned with read data, center-aligned with write data. DQS# is only used
when differential data strobe mode is enabled via the LM command. DQS9#–DQS17# are
only used when RDQS# is enabled via the LM command.
Input data mask: DM is an input mask signal for write data. Input data is masked when
DM is sampled HIGH along with that input data during a WRITE access. DM is sampled on
both edges of DQS. Although DM pins are input-only, the DM loading is designed to match
that of DQ and DQS pins. If RDQS is enabled, DQS9#–DQS17# are used only during the READ
command.
Check bits.
Serial presence-detect data: SDA is a bidirectional pin used to transfer addresses and
data into and out of the presence-detect portion of the module.
Parity error found on the address and control bus.
Power supply: 1.8V ±0.1V.
SSTL_18 reference voltage.
4
256MB: (x72, SR) 244-Pin DDR2 Mini-RDIMM
Description
Micron Technology, Inc., reserves the right to change products or specifications without notice.
Pin Assignments and Descriptions
©2005 Micron Technology, Inc. All rights reserved.