MT4LSDT464LHG-13EG4 Micron Technology Inc, MT4LSDT464LHG-13EG4 Datasheet - Page 16
![MODULE SDRAM 32MB 144SODIMM](/photos/7/83/78349/mfg_mt_sodimm_series_sml.jpg)
MT4LSDT464LHG-13EG4
Manufacturer Part Number
MT4LSDT464LHG-13EG4
Description
MODULE SDRAM 32MB 144SODIMM
Manufacturer
Micron Technology Inc
Datasheet
1.MT4LSDT864HY-133G2.pdf
(22 pages)
Specifications of MT4LSDT464LHG-13EG4
Memory Type
SDRAM
Memory Size
32MB
Speed
133MHz
Package / Case
144-SODIMM
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Notes
09005aef80748a77
SD4C4_8_16X64HG.fm - Rev. C 6/04 EN
10.
12. Other input signals are allowed to transition no
13. IDD specifications are tested after the device is
14. Timing actually specified by
11. AC timing and I
1. All voltages referenced to V
2. This parameter is sampled. V
3. I
4. Enables on-chip refresh and address counters.
5. The minimum specifications are used only to
6. An initial pause of 100µs is required after power-
7. AC characteristics assume
8. In addition to meeting the transition rate specifi-
9. Outputs measured at 1.5V with equivalent load:
f = 1 MHz; T
1.4V.
rates. Specified values are obtained with mini-
mum cycle time and the outputs open.
indicate cycle time at which proper operation
over the full temperature range is ensured (Com-
mercial temperature: 0°C
trial Temperature: -40°C T
up, followed by two AUTO REFRESH commands,
before proper device operation is ensured. (V
and V
V
two AUTO REFRESH command wake-ups should
be repeated any time the
ment is exceeded.
cation, the clock and CKE must transit between
V
tonic manner.
t
the open circuit condition; it is not a reference to
V
t
with timing referenced to 1.5V crossover point. If
the input transition time is longer than 1ns, then
the timing is referenced at V
and no longer at the 1.5V crossover point.
more than once every two clocks and are other-
wise at valid V
properly initialized.
fied as a reference only at minimum cycle rate.
HZ defines the time at which the output achieves
OH before going High-Z.
DD
OH
SS
IH
and V
and V
is dependent on output loading and cycle
or V
DD
OL
Q must be powered up simultaneously.
SS
IL
. The last valid data element will meet
Q must be at the same potential.) The
(or between V
A
IH
DD
= 25°C; pin under test biased at
Q
or V
tests have V
IL
levels.
50pF
t
IL
SS
T = 1ns.
IL
T
A
t
REF refresh require-
.
A
and V
(MAX) and V
t
CKS; clock(s) speci-
IL
DD
+85°C).
= 0V and V
+70°C and Indus-
, V
IH
DD
) in a mono-
Q = +3.3V;
IH
IH
(MIN)
= 3V,
DD
16
15. Timing actually specified by
16. Timing actually specified by
17. Required clocks are specified by JEDEC function-
18. The I
19. Address transitions average one transition every
20. CLK must be toggled a minimum of two times
21. Based on
22. V
23. The clock frequency must remain constant (stable
24. Auto precharge mode only. The precharge timing
25. Precharge mode only.
26. JEDEC and PC100 specify three clocks.
27.
28. Parameter guaranteed by design.
29. For -10E, CL= 2 and
30. CKE is HIGH during refresh command period
31. The value of
32. Refer to device data sheet for timing waveforms.
33. Leakage number reflects the worst case leakage
32MB, 64MB, 128MB (x64, SR)
specified as a reference only at minimum cycle
rate.
ality and are not dependent on any timing param-
eter.
tionally according to the amount of frequency
alteration for the test condition.
two clocks.
during this period.
width
greater than one third of the cycle rate. V
shoot: V
clock is defined as a signal cycling within timing
constraints specified for the clock pin) during
access or precharge states (READ, WRITE, includ-
ing
be used to reduce the data rate.
budget (
and 7ns for -10E after the first clock delay, after
the last WRITE is executed. May not exceed limit
set for precharge mode.
t
and is guaranteed by design.
and
t
actually a nominal value and does not result in a
fail value.
ule SPDs is calculated from
possible through the module pin, not what each
memory device contributes.
AC for -133/-13E at CL = 3 with no load is 4.6ns
RFC (MIN) else CKE is LOW. The I
Micron Technology, Inc., reserves the right to change products or specifications without notice.
-133 and -13E.
IH
t
overshoot: V
WR, and PRECHARGE commands). CKE may
t
CK = 7.5ns; for -13E, CL = 2 and
DD
144-PIN SDRAM SODIMM
IL
current will increase or decrease propor-
t
RP) begins 7ns for -13E; 7.5ns for -133
3ns, and the pulse width cannot be
t
(MIN) = -2V for a pulse width 3ns.
CK = 10ns for -10E, and
t
RAS used in -13E speed grade mod-
IH
(MAX) = V
t
CK = 10ns; for -133, CL = 3
©2004 Micron Technology, Inc. All rights reserved.
t
RC -
t
t
WR plus
WR.
DD
Q + 2V for a pulse
t
RP = 45ns.
t
CK = 7.5ns for
t
CK = 7.5ns.
t
DD
RP; clock(s)
6 limit is
IL
under-