MT36VDDF25672Y-265D2 Micron Technology Inc, MT36VDDF25672Y-265D2 Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/4/441/micron_technology_inc_sml.jpg)
MT36VDDF25672Y-265D2
Manufacturer Part Number
MT36VDDF25672Y-265D2
Description
MODULE SDRAM DDR 2GB 184DIMM
Manufacturer
Micron Technology Inc
Datasheet
1.MT36VDDF25672G-335D2.pdf
(37 pages)
Specifications of MT36VDDF25672Y-265D2
Memory Type
DDR SDRAM
Memory Size
2GB
Speed
266MT/s
Package / Case
184-DIMM
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
General Description
speed CMOS, dynamic random-access, 1GB and 2GB
memory module organized in x72 (ECC) configuration.
DDR SDRAM modules use internally configured quad-
bank DDR SDRAM devices.
tecture to achieve high-speed operation. Double data
rate architecture is essentially a 2n-prefetch architec-
ture with an interface designed to transfer two data
words per clock cycle at the I/O pins. A single read or
write access for DDR SDRAM modules effectively con-
sists of a single 2n-bit wide, one-clock-cycle data
transfer at the internal DRAM core and two corre-
sponding n-bit wide, one-half-clock-cycle data trans-
fers at the I/O pins.
externally, along with data, for use in data capture at
the receiver. DQS is an intermittent strobe transmitted
by the DDR SDRAM during READs and by the memory
controller during WRITEs. DQS is edge-aligned with
data for READs and center-aligned with data for
WRITEs.
clock inputs (CK and CK#); the crossing of CK going
HIGH and CK# going LOW will be referred to as the
positive edge of CK. Commands (address and control
signals) are registered at every positive edge of CK.
Input data is registered on both edges of DQS, and out-
put data is referenced to both edges of DQS, as well as
to both edges of CK.
are burst oriented; accesses start at a selected location
and continue for a programmed number of locations
in a programmed sequence. Accesses begin with the
registration of an ACTIVE command, which is then fol-
lowed by a READ or WRITE command. The address
bits registered coincident with the ACTIVE command
are used to select the device bank and row to be
accessed (BA0, BA1 select devices bank; A0–A12 select
device row). The address bits registered coincident
with the READ or WRITE command are used to select
the device bank and starting device column location
for the burst access.
read or write burst lengths of 2, 4, or 8 locations. An
auto precharge function may be enabled to provide a
self-timed row precharge that is initiated at the end of
the burst access.
SDRAM modules allows for concurrent operation,
thereby providing high effective bandwidth by hiding
row precharge and activation time.
pdf: 09005aef80772fd2, source: 09005aef8075ebf6
DDF36C128_256x72G.fm - Rev. D 9/04 EN
MT36VDDF12872 and MT36VDDF25672 are high-
DDR SDRAM modules use a double data rate archi-
A bidirectional data strobe (DQS) is transmitted
DDR SDRAM modules operate from differential
Read and write accesses to DDR SDRAM modules
DDR SDRAM modules provide for programmable
The pipelined, multibank architecture of DDR
10
power-saving power-down mode. All inputs are com-
patible with the JEDEC Standard for SSTL_2. All out-
puts are SSTL_2, Class II compatible.
information regarding DDR SDRAM operation, refer to
the 256Mb or 512Mb DDR SDRAM component data
sheet.
PLL and Register Operation
where the command/address input signals are latched
in the registers on the rising clock edge and sent to the
DDR SDRAM devices on the following rising clock
edge (data access is delayed by one clock cycle). A
phase-lock loop (PLL), on the module, receives and
redrives the differential clock signals (CK, CK#) to the
DDR SDRAM devices. The registers and PLL minimize
system and clock loading.
Serial Presence-Detect Operation
detect (SPD). The SPD function is implemented using
a 2,048-bit EEPROM. This nonvolatile storage device
contains 256 bytes. The first 128 bytes can be pro-
grammed by Micron to identify the module type and
various SDRAM organizations and timing parameters.
The remaining 128 bytes of storage are available for
use by the customer. System READ/WRITE operations
between the master (system logic) and the slave
EEPROM device (DIMM) occur via a standard I
using the DIMM’s SCL (clock) and SDA (data) signals,
together with SA (2:0), which provide eight unique
DIMM/EEPROM addresses. Write protect (WP) is tied
to ground on the module, permanently disabling hard-
ware write protect.
Mode Register Definition
mode of operation of DDR SDRAM devices. This defi-
nition includes the selection of a burst length, a burst
type, a CAS latency and an operating mode, as shown
in Figure 7, Mode Register Definition Diagram, on
page 11. The mode register is programmed via the
MODE REGISTER SET command (with BA0 = 0 and
BA1 = 0) and will retain the stored information until it
is programmed again or the device loses power (except
for bit A8, which is self-clearing).
contents of the memory, provided it is performed cor-
rectly. The mode register must be loaded (reloaded)
when all device banks are idle and no bursts are in
An auto refresh mode is provided, along with a
DDR SDRAM modules operate in registered mode,
DDR SDRAM modules incorporate serial presence-
The mode register is used to define the specific
Reprogramming the mode register will not alter the
Micron Technology, Inc., reserves the right to change products or specifications without notice.
1GB, 2GB (x72, ECC, DR)
184-PIN DDR RDIMM
©2004 Micron Technology, Inc. All rights reserved.
For more
2
C bus