4N45#500 Avago Technologies US Inc., 4N45#500 Datasheet - Page 8
![OPTOCOUPLER DARL OUT 6-SMD](/photos/15/83/158351/94086_sml.jpg)
4N45#500
Manufacturer Part Number
4N45#500
Description
OPTOCOUPLER DARL OUT 6-SMD
Manufacturer
Avago Technologies US Inc.
Datasheet
1.4N46.pdf
(11 pages)
Specifications of 4N45#500
Input Type
DC
Package / Case
6-SMD Gull Wing
Number Of Channels
1
Voltage - Isolation
3750Vrms
Current Transfer Ratio (min)
200% @ 10mA
Current Transfer Ratio (max)
1000% @ 10mA
Voltage - Output
4.5V
Current - Output / Channel
60mA
Current - Dc Forward (if)
10mA
Output Type
Darlington with Base
Mounting Type
Surface Mount, Gull Wing
Isolation Voltage
3750 Vrms
Output Device
Photodarlington
Configuration
1 Channel
Current Transfer Ratio
2000 %
Maximum Baud Rate
100 KBps
Maximum Forward Diode Voltage
1.7 V
Maximum Reverse Diode Voltage
5 V
Maximum Input Diode Current
20 mA
Maximum Power Dissipation
100 mW
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Vce Saturation (max)
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Figure 2. Input diode forward current vs.
forward voltage.
Figure 5. Current transfer ratio vs. input
current.
Package Characteristics
For 0 C T
*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage
rating. For the continuous voltage rating refer to the VDE 0884 Insulation Characteristics Table (if applicable), your equipment level safety specification,
or Avago Application Note 1074, “Optocoupler Input-Output Endurance Voltage.”
Notes:
8
1. Derate linearly above 50 C free-air
2. Derate linearly above 50 C free-air
3. Derate linearly above 25 C free-air
4. Derate linearly above 25 C free-air
5. DC CURRENT TRANSFER RATIO is defined
Parameter
Input-Output Momentary
Withstand Voltage*
Resistance, Input-Output
Capacitance, Input-Output
temperature at a rate of 0.4 mA/ C.
temperature at a rate of 0.7 mW/ C.
temperature at a rate of 0.8 mA/ C.
temperature at a rate of 1.5 mW/ C.
as the ratio of output collector current, I
to the forward LED input current, I
100%.
A
70 C, unless otherwise specified. All typicals at T
F
, times
Symbol
V
R
C
O
,
ISO
I-O
I-O
Figure 3. Typical DC transfer characteristics.
Figure 6. Propagation delay vs. forward
current.
6. Pin 6 Open.
7. Device considered a two-terminal device:
8. Use of a resistor between pin 4 and 6 will
9. Common mode transient immunity in Logic
Min.
3750
Pins 1, 2, 3 shorted together and Pins 4, 5,
and 6 shorted together.
decrease gain and delay time. (See Figures
11, 12, and 13.)
High level is the maximum tolerable
(positive) dV
the common mode pulse, V
that the output will remain in a Logic High
Typ.
10
0.6
cm
12
/dt on the leading edge of
Max.
A
= 25 C.
CM
V
CC
, to assure
Units
V rms
= 5 V
pF
RH 50%, t = 1 min,
T
V
f = 1 MHz
A
I-O
= 25 C
Test Conditions
= 500 Vdc
Figure 4. Output current vs. input current.
Figure 7. Propagation delay vs. temperature.
10. In accordance with UL 1577, each
state (i.e., V
transient immunity in Logic Low level is
the maximum tolerable (negative)
common mode pulse signal, V
that the output will remain in a Logic Low
state (i.e., V
optocoupler is proof tested by applying an
insulation test voltage 4500 V rms for 1
second (leakage detection current limit,
I
dV
I-O
cm
/dt on the trailing edge of the
5 A).
O
O
> 2.5 V). Common mode
< 2.5 V).
Fig.
cm
V
CC
, to assure
Notes
= 5 V
7, 10
7
7