HCPL-3000 Avago Technologies US Inc., HCPL-3000 Datasheet - Page 6

• Manufacturer Part Number: HCPL-3000
• Description: OPTOCOUPLER GATE DRVR BIPOL 8DIP
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-3000

• Voltage - Isolation: 5000Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 500mA
• Propagation Delay High - Low @ If: 2µs @ 5mA
• Current - Dc Forward (if): 20mA
• Input Type: DC
• Output Type: Push-Pull, Totem-Pole
• Mounting Type: Through Hole
• Package / Case: 8-DIP (0.300", 7.62mm)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 516-1118-5

Notes:
1. Derate absolute maximum ratings with ambient temperatures as shown in Figures 9, 10, and 11.
2. A bypass capacitor of 0.01 F or more is needed near the device between V
3. I
4. Device considered a two terminal device; pins 1-4 are shorted together and pin 5-8 are shorted together.
5. For devices with minimum V
6. The t
7. R
6
Switching Specifications (T
Propagation Delay
Time to High Output
Level
Propagation Delay Time
to Low Output Level
Rise Time
Fall Time
Output High Level
Common Mode
Transient Immunity
Output Low Level
Common Mode
Transient Immunity
Package Characteristics
Input-Output Momentary
Withstand Voltage*
Resistance
(Input-Output)
Capacitance
(Input-Output)
*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage
rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equipment level
safety specification, or Avago Application Note 1074, “Optocoupler Input-Output Endurance Voltage.”
characteristics.
applying an insulation test voltage
device is turning off. For more applications and circuit design information see Application Note “Power Transistor Gate/Base
Drive Optocouplers.”
FLH
1
sets the base current (I
represents the forward current when the output goes from low to high.
PLH
Parameter
Parameter
and t
PHL
propagation delays are measured from the 50% level of the input pulse to the 50% level of the output pulse.
O1
in Figure 1) supplied to the power bipolar device. R
ISO
|CM
|CM
specified at 5000 V rms, in accordance with UL1577, each optocoupler is proof-tested by
Sym.
Sym.
t
t
V
R
C
A
PLH
PHL
t
t
ISO
I-O
I-O
r
f
= 25 C)
H
L
6000 V rms for one second (leakage current detection limit, I
|
|
Min.
5x10
5000
Min.
10
10
-
-
-
-
–
10
Typ.
0.2
0.1
Typ.
10
1.2
2
2
-
-
11
Max.
Max.
5
5
1
1
-
-
–
–
kV/ s
kV/ s
Units
V rms
Units
pF
s
CC
and GND when measuring output and transfer
V
R
V
I
R
V
I
R
F
F
CC
CM
CM
L1
L2
L2
RH = 40% to 60%,
t = 1 min., T
V
RH = 40% to 60%
f = 1 MHz
2
= 5mA, R
= 0 mA, R
I-O
limits the peak current seen by Q2 when the
= 5 , R
= 1 k , V
= 1 k , V
= 6 V, I
= 600 V
= 600 V
= 500 V, T
Test Conditions
Test Conditions
F
L1
= 5 mA,
L1
L2
Peak
Peak
A
= 470 ,
02H
02L
= 470 ,
= 10
= 25 C
A
,
,
= 25 C,
= 0.5 V
= 0.5 V
I-O
200 A).
Fig.
Fig.
24,
25
7,
8
Note
2, 6
Note
4, 5
2
4
4