HCPL-5120-300 Avago Technologies US Inc., HCPL-5120-300 Datasheet
HCPL-5120-300
Specifications of HCPL-5120-300
Related parts for HCPL-5120-300
HCPL-5120-300 Summary of contents
Page 1
... The voltage and current supplied by this opto- coupler makes it ideally suited for directly driving IGBTs with ratings up to 200 V/00 A. For IGBTs with higher ratings, the HCPL-520 can be used to drive a discrete power stage, which drives the IGBT gate. The products are capable of operation and storage ...
Page 2
... COUNTRY OF MFR. AVAGO CAGE CODE* 8.13 (0.320) MAX. 7.16 (0.282) 7.57 (0.298) 4.32 (0.170) MAX. 0.20 (0.008) MIN. 0.33 (0.013) 7.36 (0.290) 7.87 (0.310) HCPL-5120 HCPL-5121 Gold Plate Option - 200 Option - 100 Option - 300 5962- 0420401HPX 0420401HPC 0420401HPA 0420401HYC 0420401HYA 0420401HXA ...
Page 3
Hermetic Optocoupler Options Option Description 100 Surface mountable hermetic optocoupler with leads trimmed for butt joint assembly. This option is available on commercial and hi-rel product (see drawings below for details). 0.51 (0.020) MIN. 2.29 (0.090) 2.79 (0.110) NOTE: DIMENSIONS ...
Page 4
Absolute Maximum Ratings Parameter Storage Temperature Operating Temperature Case Temperature Junction Temperature Lead Solder Temperature Average Input Current Peak Transient Input Current (<1 µs pulse width, 300 pps) Reverse Input Voltage “High” Peak Output Current “Low” Peak Output Current Supply ...
Page 5
Electrical Specifications (DC) Over recommended operating conditions ( Ground), unless otherwise specified. EE Parameter Symbol Test Conditions High Level Output Current V = (VCC - Low Level ...
Page 6
Switching Specifications (AC) Over recommended operating conditions ( Ground), unless otherwise specified. EE Parameter Symbol Propagation Delay Time t PLH to High Output Level Propagation Delay Time t PHL to Low Output Level Pulse Width Distortion PWD ...
Page 7
... This is a momentary withstand test, not an operating condition. 6. Device considered a two-terminal device: pins on input side shorted together and pins on output side shorted together. . The difference between t and t between any two HCPL-520 parts under the same test condition. PHL PLH 8. Pins and 4 need to be connected to LED common. ...
Page 8
I = 10mA to 18mA -100mA OUT 30V -55 -35 - 105 125 TEMPERATURE - ...
Page 9
I = 10mA 30V Ω 400 Duty Cycle = 50 10khz A 300 200 T PLH T ...
Page 10
Figure 17. I Test Circuit 0.1 µ ...
Page 11
500 Ω KHz 50% DUTY 3 CYCLE < Figure 23 and t Test Circuit and ...
Page 12
... Applications Information Eliminating Negative IGBT Gate Drive To keep the IGBT firmly off, the HCPL-520 has a very low maximum V specification of 0.5 V. The HCPL-520 OL realizes this very low V by using a DMOS transistor OL Ω with (typical) on resistance in its pull down circuit. When the HCPL-5 the low state, the IGBT gate + Ω ...
Page 13
... Without a detector shield, the dominant cause of op- tocoupler CMR failure is capacitive coupling from the input side of the optocoupler, through the package, to the detector IC as shown in Figure 28. The HCPL-520 improves CMR performance by using a detector IC with an optically transparent Faraday shield, which diverts the capacitively coupled current away from the sensitive IC circuitry ...
Page 14
CMR with the LED On (CMR ). H A high CMR LED drive circuit must keep the LED on dur- ing common mode transients. This is achieved by over- driving the LED current beyond the input threshold so that it ...
Page 15
... The maximum dead time is equivalent to the difference between the maximum and minimum propagation delay difference specifications as shown in Figure 34. The maximum dead time for the HCPL-5 350 ns - (-350 ns)) over an operating tempera- ture range of -55°C to 25°C. Note that the propagation delays used to calculate PDD ...
Page 16
... Turn Off Delay, of 0.6 µs. When the HCPL-520 output is in the low state and the supply voltage rises above the HCPL-520 V old (.0 < V < 3.5) the optocoupler output will go � ...