HCPL-5500#200 Avago Technologies US Inc., HCPL-5500#200 Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/0/86/avago_technologies_us_inc__sml.jpg)
HCPL-5500#200
Manufacturer Part Number
HCPL-5500#200
Description
OPTOCOUPLER TRANS OUT 8-DIP
Manufacturer
Avago Technologies US Inc.
Datasheet
1.HCPL-5500.pdf
(13 pages)
Specifications of HCPL-5500#200
Input Type
DC
Package / Case
8-DIP (0.300", 7.62mm)
Voltage - Isolation
1500VDC
Number Of Channels
1, Unidirectional
Current - Output / Channel
8mA
Data Rate
400kbps
Propagation Delay High - Low @ If
400ns @ 16mA
Current - Dc Forward (if)
20mA
Output Type
Open Collector
Mounting Type
Through Hole
Output Device
Phototransistor
Configuration
1 Channel
Current Transfer Ratio
20 %
Maximum Baud Rate
400 KBps
Maximum Forward Diode Voltage
1.9 V
Maximum Input Diode Current
20 mA
Maximum Power Dissipation
200 mW
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 55 C
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Typical Characteristics
All typical values are at T
Multi-Channel Product Only
Notes:
1. Each channel of a multi-channel device.
2. Current Transfer Ratio is defined as the ratio of output collector current, I
3. All devices are considered two-terminal devices; measured between all input leads or terminals shorted together and all output leads or terminals
4. The 4N55, 4N55/883B, HCPL-257K, HCPL-6530, HCPL-6531, and HCPL-653K dual channel parts function as two independent single channel units.
5. Measured between adjacent input pairs shorted together for each multichannel device.
6. t
7. CM
8. Bandwidth is the frequency at which the ac output voltage is 3 dB below the low frequency asymptote. For the HCPL-5530 the typical bandwidth
9. This is a momentary withstand test, not an operating condition.
10. Higher CTR minimums are available to support special applications.
11. Measured between each input pair shorted together and all output connections for that channel shorted together.
12. Standard parts receive 100% testing at 25°C (Subgroups 1 and 9). SMD and 883B parts receive 100% testing at 25, 125, and -55°C (Subgroups 1
13. Not required for 4N55, 4N55/883B, HCPL-257K, 5962-8767901, and 5962-8767905 types.
14. Required for 4N55, 4N55/883B, HCPL-257K, 5962-8767901, and 5962-8767905 types only.
9
Parameter
Input Capacitance
Input Diode Temperature
Coefficient
Resistance (Input-Output)
Capacitance (Input-Output)
Transistor DC Current Gain
Small Signal Current Transfer Ratio
Common Mode Transient Immu-
nity at Logic High Level Output
Common Mode Transient Immu-
nity at Logic Low Level Output
Bandwidth
Parameter
Input-Input Insulation Leakage
Current
Resistance (Input-Input)
Capacitance (Input-Input)
degrade slightly over the unit’s lifetime as a function of input current, temperature, signal duty cycle, and system on time. Refer to Application
Note 1002 for more detail. ln short, it is recommended that designers allow at least 20-25% guardband for CTR degradation.
shorted together.
Use the single channel parameter limits. I
output pulse. The t
ing edge of the output pulse.
CM
V).
is 2 MHz.
and 9, 2 and 10, 3 and 11, respectively).
PHL
L
H
propagation delay is measured from the 50% point on the leading edge of the input pulse to the 1.5 V point on the leading edge of the
is the maximum rate of rise of the common mode voltage that can be sustained with the output voltage in the logic low state (V
is the maximum rate of fall of the common mode voltage that can be sustained with the output voltage in the logic high state (V
PLH
propagation delay is measured from the 50% point on the trailing edge of the input pulse to the 1.5 V point on the trail-
A
= 25°C, V
CC
F
Symbol
C
DV
R
C
h
DI
|CM
|CM
BW
Symbol
I
R
C
= 0 mA for channel under test and I
I-O
I-I
IN
I-O
FE
= 5 V, unless otherwise specified.
O
I-I
I-I
F
/DI
/DT
H
L
|
|
F
A
Test Conditions
V
I
V
f = 1 MHz
V
V
I
V
V
I
V
V
Test Conditions
RH
V
f=1 MHz
F
F
F
F
I-O
O
CC
O
CM
O
CM
I-I
= 20 mA
= 0 mA, R
= 16 mA, R
= 0 V, f = 1 MHz
= 5 V, I
(min) = 2.0 V,
(max) = 0.8 V,
= 500 V
≤
= 5 V, V
= 500 V
= 10 V
= 10 V
65%, V
O
P-P
P-P
O
= 3 mA
L
I-I
L
= 8.2 kW,
= 2 V
O
= 8.2 kW,
= 500 V, t = 5 s
, to the forward LED input current, I
F
= 20 mA for other channels.
Typ.
60
-1.5
10
1.0
250
21
1000
-1000
9
12
Units
pF
mV/°C
W
pF
-
%
V/ms
V/ms
MHz
Typ.
1
10
0.8
12
F
, times 100%. CTR is known to
Fig.
7
10
10
8
Units
pA
W
pF
Notes
1
1
3
1, 11
1
1
1, 7
1, 7
8
Notes
5, 9
5
5
O
< 0.8 V).
O
> 2.0