HCPL-2430 Avago Technologies US Inc., HCPL-2430 Datasheet - Page 10
![ISOLAT 3.75KVRMS 2CH UNIDIR 8DIP](/photos/7/66/76618/516-8-dip_sml.jpg)
HCPL-2430
Manufacturer Part Number
HCPL-2430
Description
ISOLAT 3.75KVRMS 2CH UNIDIR 8DIP
Manufacturer
Avago Technologies US Inc.
Datasheet
1.HCPL-2400-300E.pdf
(15 pages)
Specifications of HCPL-2430
Voltage - Isolation
3750Vrms
Number Of Channels
2, Unidirectional
Current - Output / Channel
25mA
Data Rate
40MBd
Propagation Delay High - Low @ If
33ns @ 7mA
Current - Dc Forward (if)
10mA
Input Type
DC
Output Type
Push-Pull, Totem-Pole
Mounting Type
Through Hole
Package / Case
8-DIP (0.300", 7.62mm)
No. Of Channels
2
Isolation Voltage
3.75kV
Optocoupler Output Type
Logic Gate
Input Current
8mA
Output Voltage
18V
Opto Case Style
DIP
No. Of Pins
8
Propagation Delay Low-high
60ns
Common Mode Voltage Vcm
50V
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
516-1106-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
HCPL-2430
Manufacturer:
AVAGO
Quantity:
32 000
Part Number:
HCPL-2430
Manufacturer:
HP
Quantity:
20 000
Company:
Part Number:
HCPL-2430#300
Manufacturer:
AGILENT
Quantity:
16 000
Company:
Part Number:
HCPL-2430#300E
Manufacturer:
AVAGO
Quantity:
10 000
Company:
Part Number:
HCPL-2430#500E
Manufacturer:
AVAGO
Quantity:
10 000
Company:
Part Number:
HCPL-2430-000E
Manufacturer:
AVAGO
Quantity:
40 000
Part Number:
HCPL-2430-000E
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Part Number:
HCPL-2430-020E
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Part Number:
HCPL-2430-060E
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Part Number:
HCPL-2430-500E
Manufacturer:
AVAGO/安华高
Quantity:
20 000
10
Package Characteristics
*All typical values are at T
**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to the VDE 0884 Insulation Related Characteristics Table (if applicable), your equipment lev-
el safety specification or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage, ” publication number 5963-2203E.
Notes:
10. Power Supply Noise Immunity is the peak to peak amplitude of the ac ripple voltage on the V
11. Use of a 0.1 µF bypass capacitor connected between pins 8 and 5 adjacent to the device is required.
12. Peak Forward Input Current pulse width < 50 µs at 1 KHz maximum repetition rate.
13. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 V rms for one second (leakage detec-
1. Each channel.
2. Duration of output short circuit time not to exceed 10 ms.
3. Device considered a two terminal device: pins 1, 2, 3, and 4 shorted together, and pins 5, 6, 7, and 8 shorted together.
4. t
5. The typical data shown is indicative of what can be expected using the application circuit in Figure 13.
6. This specification simulates the worst case operating conditions of the HCPL-2400 over the recommended operating temperature and V
7. Propagation delay skew is discussed later in this data sheet.
8. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together.
9. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dV
Parameter
Input-Output
Momentary
Withstand Voltage**
Input-Output
Resistance
Input-Output
Capacitance
Input-Input
Insulation Leakage
Current
Resistance
(Input-Input)
Capacitance
(Input-Input)
output pulse. The t
rising edge of the output pulse.
with the suggested application circuit of Figure 13.
that the output will remain in a Logic High state (i.e., V
able (negative) dV
in the desired logic state. For desired logic high state, V
tion current limit, I
Characteristics Table, if applicable.
PHL
propagation delay is measured from the 50% level on the rising edge of the input current pulse to the 1.5 V level on the falling edge of the
CM
I-O
PLH
/dt of the common mode pulse, V
≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-2 Insulation Related
A
propagation delay is measured from the 50% level on the falling edge of the input current pulse to the 1.5 V level on the
= 25°C.
Sym.
V
R
C
C
R
I
ISO
I-I
I-O
I-O
I-I
I-I
Device
2430
2430
2430
CM
3750
O
Min.
OH(MIN)
, to assure that the output will remain in a Logic Low state (i.e., V
> 2.0 V). Common mode transient immunity in a Logic Low level is the maximum toler-
> 2.0 V, and for desired logic low state, V
0.005
Typ.*
0.25
10
10
0.6
12
11
Max.
Units
V rms
µA
pF
pF
Ω
Ω
CC
line that the device will withstand and still remain
Test Conditions
CM
/dt of the common mode pulse, V
RH ≤50%,
t = 1 min.,
T
V
f = 1 MHz
V
RH ≤45%
t = 5 s,
V
V
f = 1 MHz
A
I-O
I-O
I-I
I-I
= 25°C
OL(MAX)
= 500 Vdc
= 500 Vdc
= 500 Vdc
= 0 Vdc
< 0.8 V.
O
< 0.8 V).
Fig.
CM
, to assure
3, 13
Note
CC
3
8
8
8
range