HCPL-0723-060 Avago Technologies US Inc., HCPL-0723-060 Datasheet - Page 9
![OPTOCOUPLER 50MBD 2NS VDE 8-SOIC](/photos/7/65/76546/516-8-soic_sml.jpg)
HCPL-0723-060
Manufacturer Part Number
HCPL-0723-060
Description
OPTOCOUPLER 50MBD 2NS VDE 8-SOIC
Manufacturer
Avago Technologies US Inc.
Datasheet
1.HCPL-7723-300.pdf
(12 pages)
Specifications of HCPL-0723-060
Package / Case
8-SOIC (0.154", 3.90mm Width)
Voltage - Isolation
3750Vrms
Number Of Channels
1, Unidirectional
Current - Output / Channel
10mA
Data Rate
50MBd
Propagation Delay High - Low @ If
16ns
Input Type
Logic
Output Type
Push-Pull, Totem-Pole
Mounting Type
Surface Mount
Isolation Voltage
3750 Vrms
Maximum Continuous Output Current
10 mA
Maximum Fall Time
6 ns
Maximum Rise Time
8 ns
Output Device
Logic Gate Photo IC
Configuration
1 Channel
Maximum Baud Rate
50 MBps
Maximum Power Dissipation
150 mW
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Package Characteristics
All Typical Specifications are at T
Parameter
Input-Output Momentary
Withstand Voltage
Input-Output Resistance
Input-Output Capacitance
Input Capacitance
Input IC Junction-to-Case
Thermal Resistance
Output IC Junction-to-Case
Thermal Resistance
Package Power Dissipation
Notes:
1. Absolute Maximum ambient operating temperature means the device will not be damaged if operated under these conditions. It does not
2. The LED is ON when V
3. t
4. PWD is defined as |t
5. t
6. CMH is the maximum common mode voltage slew rate that can be sustained while maintaining V
7. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together.
8. In accordance with UL1577, each HCPL-0723 is proof tested by applying an insulation test voltage ≥ 4500 Vrms for 1 second (leakage detec-
9. The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
10. C
9
guarantee functionality.
nal. t
signal.
within the recommended operating conditions.
mon mode voltage slew rate that can be sustained while maintaining V
and falling common mode voltage edges.
tion current limit, I
tion current limit. I
voltage rating. For the continuous voltage rating refer to your equipment level safety specification or Avago Application Note 1074 entitled
“Optocoupler Input-Output Endurance Voltage. ”
PHL
PSK
I
is the capacitance measured at pin 2 (V
is equal to the magnitude of the worst case difference in t
propagation delay is measured from the 50% level on the falling edge of the VI signal to the 50% level of the falling edge of the V
PLH
propagation delay is measured from the 50% level on the rising edge of the VI signal to the 50% level of the rising edge of the V
[10]
[7,8,9]
I-O
I-O
[7]
PHL
≤ 5 µA). Each HCPL-7723 is proof tested by applying an insulation test voltage ≥ 4500 Vrms for 1 second (leakage detec-
≤ 5 µA.)
I
is low and OFF when V
- t
PLH
A
= 25°C.
|. %PWD (percent pulse width distortion) is equal to the PWD divided by pulse width.
–7723
Option 020
–0723
–7723
–0723
–7723
–0723
I
).
I
is high.
Symbol
V
R
C
C
θ
θ
P
ISO
PD
I-O
I-O
I
jci
jco
Min.
3750
5000
3750
PHL
and/or t
O
Typ.
10
0.6
3.0
145
160
145
135
< 0.8 V. The common mode voltage slew rates apply to both rising
PLH
12
that will be seen between units at any given temperature
Max.
150
Units
V rms
Ω
pF
pF
°C/W
°C/W
mW
O
> 0.8 V
Test Conditions
RH ≤ 50%, t = 1 min,
T
V
f = 1 MHz
Thermocouple located at
center underside of package
A
I-O
DD2
= 25°C
= 500 V dc
. CML is the maximum com-
O
sig-
O