HCPL-2533 Avago Technologies US Inc., HCPL-2533 Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/0/86/avago_technologies_us_inc__sml.jpg)
HCPL-2533
Manufacturer Part Number
HCPL-2533
Description
OPTOCOUPLER 8-DIP
Manufacturer
Avago Technologies US Inc.
Datasheet
1.HCPL-2533500.pdf
(11 pages)
Specifications of HCPL-2533
Input Type
DC
Package / Case
8-DIP (0.300", 7.62mm)
Voltage - Isolation
3750Vrms
Number Of Channels
2, Unidirectional
Current - Output / Channel
8mA
Data Rate
250kbps
Propagation Delay High - Low @ If
800ns @ 8mA
Current - Dc Forward (if)
25mA
Output Type
Open Collector
Mounting Type
Through Hole
Isolation Voltage
3750 Vrms
Maximum Forward Diode Current
8 mA
Output Device
Phototransistor
Configuration
2 Channel
Current Transfer Ratio
22 %
Maximum Baud Rate
1 MBps
Maximum Forward Diode Voltage
1.7 V
Maximum Reverse Diode Voltage
5 V
Maximum Input Diode Current
25 mA
Maximum Power Dissipation
45 mW
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
HCPL-2533
Manufacturer:
AVAGO
Quantity:
1 000
Company:
Part Number:
HCPL-2533-000E
Manufacturer:
AVAGO
Quantity:
5 000
Company:
Part Number:
HCPL-2533-300E
Manufacturer:
AVAGO
Quantity:
5 000
Company:
Part Number:
HCPL-2533-500E
Manufacturer:
AVAGO
Quantity:
5 000
Electrical Specifications
Over recommended temperature (T
Parameter
Logic High
Output Current
Logic High
Supply Current
Input Reverse
Breakdown Voltage
Input Capacitance
Input-Output
Insulation Leakage
Current
Resistance
(Input–Output)
Capacitance
(Input–Output)
Input–Input
Insulation Leakage
Current
Resistance
(Input–Input)
Capacitance
(Input–Input)
*All typicals at 25°C.
Notes:
5. Each channel.
6. Current Transfer Ratio is defined as the ratio of output collector current, I
7. Device considered a two-terminal device: Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together.
8. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together.
9. Common mode transient immunity in Logic High level is the maximum tolerable (positive) dV
10. The 7.5 k load represents 1 LSTTL unit load of 0.36 mA and a 20 kΩ pull-up resistor.
11. The 4.7 k load represents 1 LSTTL unit load of 0.36 mA and an 8.2 kΩ pull-up resistor.
8
pulse V
the maximum tolerable (negative) dV
in a Logic Low state (i.e., V
CM
, to assure that the output will remain in a Logic High state (i.e., V
O
< 0.8 V).
Symbol
I
I
V
C
I
R
C
I
R
C
OH
CCH
I–O
I–I
R
IN
I–O
I–O
I–I
I–I
CM
A
/dt on the trailing edge of the common mode pulse signal, V
= 0°C to +70°C) unless otherwise specified.
Min.
5
Typ.*
0.5
0.05
60
10
0.6
0.005
10
0.25
12
11
Max.
50
4
1.0
O
, to the forward LED input current, I
O
> 2.0 V). Common mode transient immunity in Logic Low level is
Units
nA
µA
µA
V
pF
µA
Ω
pF
µA
Ω
pF
Test Conditions
T
I
V
I
V
I
V
V
I
f = 1 MHz, V
45% Relative Humidity,
t = 5s
V
T
V
f = 1 MHz
45% Relative Humidity,
t = 5s
V
V
f = 1 MHz
F1
F1
F1
F
A
A
O1
O1
O1
CC
I–O
I–O
I–I
I–I
= 10 µA, T
= 25°C,
= 25°C
CM
= I
= I
= I
= 500 Vdc
= 500 Vdc
= 5.5 V
= V
= V
= V
= 3000 Vdc,
= 500 Vdc
/dt on the leading edge of the common mode
F2
F2
F2
O2
O2
O2
= 0 mA
= mA
= 0 mA
CM
= V
= V
= Open,
, to assure that the output will remain
A
F
= 0 V
= 25°C
CC
CC
F
= 5.5 V
, times 100%.
= 5.5 V
Fig.
5
Note
5
5
5
5
7
7
7
8
8
8