HCPL-2300-560E Avago Technologies US Inc., HCPL-2300-560E Datasheet - Page 8
![OPTOCOUPLER 8MBD VDE 8-SMD](/photos/22/84/228410/4176142_sml.jpg)
HCPL-2300-560E
Manufacturer Part Number
HCPL-2300-560E
Description
OPTOCOUPLER 8MBD VDE 8-SMD
Manufacturer
Avago Technologies US Inc.
Datasheet
1.HCPL-2300-000E.pdf
(14 pages)
Specifications of HCPL-2300-560E
Voltage - Isolation
3750Vrms
Number Of Channels
1, Unidirectional
Current - Output / Channel
25mA
Data Rate
8MBd
Propagation Delay High - Low @ If
110ns @ 500µA ~ 750µA
Current - Dc Forward (if)
5mA
Input Type
DC
Output Type
Open Collector
Mounting Type
Surface Mount, Gull Wing
Package / Case
8-SMD Gull Wing
No. Of Channels
1
Optocoupler Output Type
Logic Gate
Input Current
1mA
Output Voltage
5.25V
Opto Case Style
SMD
No. Of Pins
8
Peak Reflow Compatible (260 C)
Yes
Isolation Voltage
3.75kV
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
HCPL-2300-560E
Manufacturer:
AVAGO
Quantity:
40 000
Part Number:
HCPL-2300-560E
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Package Characteristics
For -40°C ≤T
*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage
rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equipment level
safety specification, or Avago Application Note 1074, “Optocoupler Input-Output Endurance Voltage. ”
Notes:
1. Bypassing the power supply line is required with a 0.1 µF ceramic
2. Peaking circuits may produce transient input currents up to 100
3. Device considered a two terminal device: pins 1, 2, 3, and 4 shorted
4. The t
Figure 2. Typical input diode forward charac-
teristics.
8
Parameter
Input-Output Momentary
Withstand Voltage*
Resistance, Input-Output
Capacitance, Input-Output
disc capacitor adjacent to each optocoupler as illustrated in Figure
19. The power supply bus for the optocoupler(s) should be separate
from the bus for any active loads, otherwise a larger value of bypass
capacitor (up to 0.5 µF) may be needed to suppress regenerative
feedback via the power supply.
mA, 500 ns maximum pulse width, provided average current does
not exceed 5 mA.
together, and pins 5, 6, 7, and 8 shorted together.
trailing edge of the input pulse to the 1.5 V point on the trailing
edge of the output pulse.
PLH
propagation delay is measured from the 50% point on the
A
≤85°C, unless otherwise specified. All typicals at T
Symbol Min.
V
R
C
I-O
ISO
I-O
Figure 3. Typical output voltage vs. forward
input current vs. temperature.
3750
Typ.
1012
0.6
Max.
5. The t
6. CM
7. CM
8. C
9. In accordance with UL 1577, each optocoupler is momentary with-
leading edge of the input pulse to the 1.5 V point on the leading
edge of the output pulse.
voltage to assure that the output will remain in a high logic state
(i.e., V
voltage to assure that the output will remain in a low logic state
(i.e., V
stand proof tested by applying an insulation test voltage ≥4500
Vrms for 1 second (leakage detection current limit, I
test is performed before the 100% production test for partial dis-
charge (Method b) shown in the IEC/EN/DIN EN 60747-5-2 Insula-
tion Characteristics Table, if applicable.
A
P
= 25°C.
is the peaking capacitance. Refer to test circuit in Figure 8.
H
L
is the maximum tolerable rate of fall of the common mode
is the maximum tolerable rate of rise of the common mode
PHL
OUT
OUT
Units
V
Ω
pF
propagation delay is measured from the 50% point on the
rms
> 2.0 V).
< 0.8 V).
Test Conditions
RH ≤ 50%, t = 1 min,
T
V
f = 1 MHz
A
I-O
= 25°C
= 500 V
Figure 4. Typical logic high output current vs.
temperature.
Fig.
I-O
≤ 5 µA). This
Notes
3, 9
3
3