HCPL-7710-520E Avago Technologies US Inc., HCPL-7710-520E Datasheet - Page 12
![OPTOCOUPLER 12MBD UL 8-SMD](/photos/15/83/158318/dual_inline_gull_wing_sml.jpg)
HCPL-7710-520E
Manufacturer Part Number
HCPL-7710-520E
Description
OPTOCOUPLER 12MBD UL 8-SMD
Manufacturer
Avago Technologies US Inc.
Datasheet
1.HCPL-7710-000E.pdf
(18 pages)
Specifications of HCPL-7710-520E
Package / Case
8-SMD Gull Wing
Voltage - Isolation
5000Vrms
Number Of Channels
1, Unidirectional
Current - Output / Channel
10mA
Data Rate
12.5MBd
Propagation Delay High - Low @ If
20ns
Input Type
Logic
Output Type
Push-Pull, Totem-Pole
Mounting Type
Surface Mount, Gull Wing
Isolation Voltage
3750 Vrms
Maximum Continuous Output Current
10 mA
Maximum Fall Time
8 ns
Maximum Forward Diode Current
10 mA
Maximum Rise Time
9 ns
Output Device
Logic Gate Photo IC
Configuration
1 Channel
Maximum Baud Rate
12.5 MBps
Maximum Power Dissipation
150 mW
Maximum Operating Temperature
+ 100 C
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
HCPL-7710-520E
Manufacturer:
AVAGO
Quantity:
10 000
12
Digital Field Bus Communication Networks
To date, despite its many drawbacks, the 4 - 20 mA
analog current loop has been the most widely accepted
standard for implementing process control systems.
In today’s manufacturing environment, however,
automated systems are expected to help manage
the process, not merely monitor it. With the advent
of digital field bus communication networks such as
DeviceNet, PROFIBUS, and Smart Distributed Systems
(SDS), gone are the days of constrained information.
Figure 17. Typical field bus communication physical model.
Optical Isolation for Field Bus Networks
To recognize the full benefits of these networks, each
recommends providing galvanic isolation using Avago
optocouplers. Since network communication is bi-direc-
tional (involving receiving data from and transmitting
data onto the network), two Avago optocouplers are
needed. By providing galvanic isolation, data integrity is
retained via noise reduction and the elimination of false
signals. In addition, the network receives maximum pro-
tection from power system faults and ground loops.
Within an isolated node, such as the DeviceNet Node
shown in Figure 18, some of the node’s components are
referenced to a ground other than V- of the network.
CONFIGURATION
TRANSCEIVER
INTERFACE
ISOLATION
OPTICAL
DEVICE
BUS
TRANSCEIVER
CONTROLLER
INTERFACE
ISOLATION
OPTICAL
BUS
TRANSCEIVER
INTERFACE
ISOLATION
STARTER
OPTICAL
MOTOR
BUS
HCPL-0710 fig 16
FIELD BUS
TRANSCEIVER
CONTROLLER
INTERFACE
ISOLATION
OPTICAL
XXXXXX
YYY
MOTOR
BUS
Controllers can now receive multiple readings from field
devices (sensors, actuators, etc.) in addition to diagnos-
tic information.
The physical model for each of these digital field bus
communication networks is very similar as shown in
Figure 17. Each includes one or more buses, an interface
unit, optical isolation, transceiver, and sensing and/or
actuating devices.
These components could include such things as devices
with serial ports, parallel ports, RS232 and RS485 type
ports. As shown in Figure 18, power from the network is
used only for the transceiver and input (network) side of
the optocouplers.
Isolation of nodes connected to any of the three types of
digital field bus networks is best achieved by using the
HCPL-x710 optocouplers. For each network, the HCPL-
x710 satisify the critical propagation delay and pulse
width distortion requirements over the temperature
range of 0°C to +85°C, and power supply voltage range
of 4.5 V to 5.5 V.
TRANSCEIVER
INTERFACE
ISOLATION
OPTICAL
BUS
SENSOR