HCPL-3180-500E Avago Technologies US Inc., HCPL-3180-500E Datasheet - Page 7
![OPTOCOUPLER DRVR 2.5A 8-SMD](/photos/22/84/228410/4176142_sml.jpg)
HCPL-3180-500E
Manufacturer Part Number
HCPL-3180-500E
Description
OPTOCOUPLER DRVR 2.5A 8-SMD
Manufacturer
Avago Technologies US Inc.
Datasheet
1.HCPL-3180-000E.pdf
(16 pages)
Specifications of HCPL-3180-500E
Voltage - Isolation
3750Vrms
Number Of Channels
1, Unidirectional
Current - Output / Channel
2.5A
Propagation Delay High - Low @ If
150ns @ 10mA
Current - Dc Forward (if)
16mA
Input Type
DC
Output Type
Gate Driver
Mounting Type
Surface Mount
Package / Case
8-SMD Gull Wing
No. Of Channels
1
Optocoupler Output Type
Gate Drive
Input Current
16mA
Output Voltage
20V
Opto Case Style
SMD
No. Of Pins
8
Propagation Delay Low-high
0.2µs
Isolation Voltage
3.75kV
Number Of Elements
1
Forward Voltage
1.8V
Forward Current
25mA
Package Type
PDIP SMD
Operating Temp Range
-40C to 100C
Power Dissipation
295mW
Propagation Delay Time
200ns
Pin Count
8
Mounting
Surface Mount
Reverse Breakdown Voltage
5V
Operating Temperature Classification
Industrial
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
HCPL-3180-500E
Manufacturer:
AVAGO
Quantity:
10 000
Part Number:
HCPL-3180-500E
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Switching Specifications (AC)
Over recommended operating conditions unless otherwise specified.
Parameter
Notes:
1. Derate linearly above +70°C free air temperature at a rate of 0.3 mA/°C.
2. Maximum pulse width = 10 µs, maximum duty cycle = 0.2%. This value is intended to allow for component tolerances for designs with IO peak
3. Derate linearly above +70°C, free air temperature at the rate of 4.8 mW/°C.
4. Derate linearly above +70°C, free air temperature at the rate of 5.4 mW/°C. The maximum LED junction temperature should not exceed
5. Maximum pulse width = 50 µs, maximum duty cycle = 0.5%.
6. In this test, V
7. Maximum pulse width = 1 ms, maximum duty cycle = 20%.
8. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 4500 V
9. Device considered a two-terminal device: pins on input side shorted together and pins on output side shorted together.
10. PWD is defined as |t
11. Pin 1 and 4 need to be connected to LED common.
12. Common mode transient immunity in the high state is the maximum tolerable dV
13. Common mode transient immunity in a low state is the maximum tolerable dV
14. t
15. The difference between t
7
Package Characteristics
Parameter
Propagation Delay Time to
High Output Level
Propagation Delay Time to
Low Output Level
Pulse Width Distortion
Propagation Delay
Difference Between Any
Two Parts or Channels
Rise Time
Fall Time
UVLO turn On Delay
UVLO turn Off Delay
Output High Level Common
Mode Transient Immunity
Output Low Level Common
Mode Transient Immunity
Input-Output Momentary
Withstand Voltage
Input-Output Resistance
Input-Output Capacitance
minimum = 2.0 A. See Application section for additional details on limiting IOL peak.
+125°C.
tion current limit I
output will remain in the high state (i.e. V
put will remain in a low state (i.e. V
signal. t
V
PHL
O
signal.
propagation delay is measured from the 50% level on the falling edge of the input pulse to the 50% level of the falling edge of the V
PLH
propagation delay is measured from the 50% level on the rising edge of the input pulse to the 50% level of the rising edge of the
OH
is measured with a dc load current. When driving capacitive load V
I-O
PHL
< 5 µA).
- t
PHL
PLH
| for any given device.
and t
PLH
O
Symbol
t
t
PWD
PDD
(t
t
t
t
t
|CM
|CM
< 1.0 V).
PLH
PHL
r
f
UVLO ON
UVLO OFF
between any two HCPL-3180 parts under same test conditions.
PHL-
Symbol
V
R
C
ISO
I-O
I-O
H
L
O
|
t
|
> 10.0 V).
PLH
)
Min.
50
50
-90
10
10
Min.
3750
Typ.
150
150
20
25
25
2.0
0.3
Typ.
10
1
[11]
Max.
200
200
65
90
CM
Max.
/dt of the common mode pulse, V
CM
OH
/dt of the common mode pulse V
will approach V
Units
ns
ns
ns
ns
ns
ns
µs
µs
kV/µs
kV/µs
Units
V
Ω
pF
rms
Test
Conditions
I
R
f = 250 kHz,
Duty Cycle = 50%,
C
CL = 1 nF,
R
T
I
V
V
F =
F
A
g
g
g
CM
CC
= 10 to 16 mA,
CC
= 25°C,
= 10 Ω,
= 0 Ω
= 10 nF
Test
Conditions
T
RH < 50%
V
Freq = 1 MHz
10 mA,
= 20 V
A
as I
= 1.5 kV,
I-O
= 25°C,
= 500 V
OH
rms
approaches zero amps.
for 1 second (leakage detec-
CM
CM
, to assure that the out-
to assure that the
Fig.
Fig.
10, 11,
12, 13,
14, 23
34, 35
23
22
22
24
24
Note
8,9
9
Note
14
10
10
11, 12
11, 13
O