HCPL-J314-300E Avago Technologies US Inc., HCPL-J314-300E Datasheet - Page 8

• Manufacturer Part Number: HCPL-J314-300E
• Description: OPTOCOUPLER 1CH 0.6A 8-SMD GW
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-J314-300E

• Package / Case: 8-SMD Gull Wing
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 600mA
• Propagation Delay High - Low @ If: 300ns @ 8mA
• Current - Dc Forward (if): 25mA
• Input Type: DC
• Output Type: Push-Pull, Totem-Pole
• Mounting Type: Surface Mount, Gull Wing
• Isolation Voltage: 3750 Vrms
• Maximum Fall Time: 50 ns
• Maximum Forward Diode Current: 25 mA
• Maximum Rise Time: 50 ns
• Minimum Forward Diode Voltage: 1.2 V
• Output Device: Integrated Photo IC
• Configuration: 1 Channel
• Maximum Forward Diode Voltage: 1.8 V
• Maximum Reverse Diode Voltage: 3 V
• Maximum Power Dissipation: 260 mW
• Maximum Operating Temperature: + 100 C
• Minimum Operating Temperature: - 40 C
• Number Of Elements: 1
• Forward Voltage: 1.8V
• Forward Current: 25mA
• Package Type: PDIP SMD
• Operating Temp Range: -40C to 100C
• Power Dissipation: 260mW
• Propagation Delay Time: 700ns
• Pin Count: 8
• Mounting: Surface Mount
• Reverse Breakdown Voltage: 3V
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Switching Specifications (AC)
Over recommended operating conditions unless otherwise specified.
Parameter
Propagation Delay Time to High Output t
Level
Propagation Delay Time to Low Output t
Level
Propagation Delay Difference
Between Any Two Parts or Channels
Rise Time
Fall Time
Output High Level Common Mode
Transient Immunity
Output Low Level Common Mode
Transient Immunity
Package Characteristics
For each channel unless otherwise specified.
Parameter
Input-Output Momentary Withstand
Voltage
Output-Output Momentary Withstand V
Voltage
Input-Output Resistance
Input-Output Capacitance
Notes:
1. Derate linearly above 70°C free air temperature at a rate of 0.3 mA/°C.
2. Maximum pulse width = 10 µs, maximum duty cycle = 0.2%. This value is intended to allow for component tolerances for designs with I
3. Derate linearly above 85°C, free air temperature at the rate of 4.0 mW/°C.
4. Input power dissipation does not require derating.
5. Maximum pulse width = 50 µs, maximum duty cycle = 0.5%.
6. In this test, V
7. Maximum pulse width = 1 ms, maximum duty cycle = 20%.
8. In accordance with UL 1577, each HCPL-J314 optocoupler is proof tested by applying an insulation test voltage ≥ 5000 Vrms for 1 second (leakage
9. Device considered a two-terminal device: pins on input side shorted together and pins on output side shorted together.
10. PDD is the difference between t
11. Common mode transient immunity in the high state is the maximum tolerable |dVcm/dt| of the common mode pulse V
12. Common mode transient immunity in a low state is the maximum tolerable |dV
13. This load condition approximates the gate load of a 1200 V/25 A IGBT.
14. For each channel. The power supply current increases when operating frequency and Qg of the driven IGBT increases.
15. Device considered a two terminal device: Channel one output side pins shorted together, and channel two output side pins shorted together.
8
minimum = 0.4 A. See Application section for additional details on limiting I
detection current limit I
EN 60747-5-2 Insulation Characteristics Table, if applicable.
output will remain in the high state (i.e. Vo > 6.0 V).
will remain in a low state (i.e. Vo < 1.0 V).
OH
is measured with a DC load current. When driving capacitive load V
I-O
≤ 5 µA). This test is performed before 100% production test for partial discharge (method B) shown in the IEC/EN/DIN
PHL
and t
PLH
between any two parts or channels under the same test conditions.
Symbol
PDD
t
t
|CM
|CM
Symbol
V
R
C
PLH
PHL
R
F
I-O
ISO
O-O
I-O
H
L
|
|
Min.
0.1
0.1
-0.5
25
25
Min.
3750
1500
Typ.
0.2
0.3
50
50
35
35
Typ.
10
1.2
12
OL
Max.
0.7
0.7
0.5
Max.
CM
peak.
/dt| of the common mode pulse, V
OH
will approach V
Units
µs
µs
µs
ns
ns
kV/µs
kV/µs
Units
Vrms
Vrms
Ω
pF
Rg = 47 Ω, Cg = 3 nF, 10,11, 14
f = 10 kHz,
Duty Cycle = 50%,
f = 10 kHz, I
V
T
V
T
RH < 50% for 1 min.
V
Freq = 1 MHz
A
A
CC
CM
I-O
CC
= 25°C,
= 25°C,
Conditions
= 30 V
as I
= 500 V
= 1.5 kV
Conditions
OH
Test
Test
approaches zero amps.
F =
CM
8 mA,
, to assure that the output
CM
to assure that the
12,13,
14,17
18
18
Fig.
Fig.
O
Note
10
11
12
Note
8,9
15
9
peak