ACPL-W302-560E Avago Technologies US Inc., ACPL-W302-560E Datasheet
ACPL-W302-560E
Specifications of ACPL-W302-560E
Related parts for ACPL-W302-560E
ACPL-W302-560E Summary of contents
Page 1
... High speed response. x Ultra high CMR. x Bootstrappable supply current. x Available in Stretched SO-6 package x Package Clearance/Creepage at 8mm (ACPL-W302) x Safety Approval: UL1577 recognized with 3750 Vrms for 1 minute for ACPL-P302 and 5000 Vrms for 1 minute for ACPL- W302. CSA Approved. IEC/EN/DIN EN 60747-5-2 Approved V IORM V ...
Page 2
... Ordering Information ACPL-P302 is UL Recognized with 3750 Vrms for 1 minute per UL1577. ACPL-W302 is UL Recognized with 5000 Vrms for 1 minute per UL1577. Option Part number RoHS Compliant -000E -500E ACPL-P302 -060E -560E -000E -500E ACPL-W302 -060E -560E To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry ...
Page 3
... NOM. 1 ±0.250 [0.040 ±0.010] 9.7±0.250 [0.382 ±0.010] ACPL-W302 Stretched SO-6 Package 0.381 ± 0.127 [0.015 ± 0.005 7.62 [0.300] +0.127 6.807 0 +0.005 0.268 -0.000 45° 0.45 [0.018] 0.20± ...
Page 4
... Recommended Pb-Free IR Profile Recommended reflow condition as per JEDEC Standard, J-STD-020 (latest revision). Non-Halide Flux should be used. Regulatory Information The ACPL-P302/W302 is approved by the following organizations: IEC/EN/DIN EN 60747-5-2 (Option 060 only) Approval under: IEC 60747-5-5:2007 CSA Approval under CSA Component Acceptance Notice #5, File CA 88324. ...
Page 5
... Input Power Dissipation Lead Solder Temperature Solder Reflow Temperature Profile Table 4.Recommended Operating Conditions Parameter Power Supply Input Current (ON) Input Voltage (OFF) Operating Temperature 5 ACPL-P302 ACPL-W302 Units Conditions 7.0 8.0 mm Measured from input terminals to output terminals, shortest distance through air. 8.0 8.0 mm Measured from input terminals to output terminals, shortest distance path along body ...
Page 6
Table 5. Electrical Specifications (DC) Over recommended operating conditions unless otherwise specified. Parameter Symbol High Level Output Current I Low Level Output Current I High Level Output Voltage V Low Level Output Voltage V High Level Supply Current I Low ...
Page 7
... This load condition approximates the gate load of a 1200 V/20 A IGBT. 15. The power supply current increases when operating frequency and Q 7 Min. Typ. Max. ACPL-P302 3750 ACPL-W302 5000 12 10 0.6 peak between any two parts or channels under the same test conditions. ...
Page 8
T – TEMPERATURE – °C A Figure 1. V vs. Temperature. OH 0.44 0.43 0.42 0.41 0.40 0.39 -50 - 100 T – ...
Page 9
T – TEMPERATURE – °C A Figure 7. I vs. Temperature. FLH 400 300 200 100 – FORWARD LED CURRENT – mA ...
Page 10
I – FORWARD LED CURRENT – Figure 13. Transfer characteristics 500 W ...
Page 11
... IGBT drain from turning on the ACPL-P302/W302. Selecting the Gate Resistor (Rg) Step 1: Calculate R minimum from the I g cation. The IGBT and R in Figure 17 can be analyzed simple RC circuit with a voltage supplied by the ACPL- P302/W302. − ³ g ...
Page 12
... Without a detector shield, the dominant cause of opto- coupler CMR failure is capacitive coupling from the input side of the optocoupler, through the package, to the detector IC as shown in Figure 19. The ACPL-P302/W302 improves CMR performance by using a detector IC with an optically transparent Faraday shield, which diverts the capacitively coupled current away from the sensitive IC circuitry ...
Page 13
... The maximum dead time is equivalent to the difference between the maximum and minimum propagation delay difference specification as shown in Figure 25. The maximum dead time for the ACPL-P302/ W302 is 1 μs (= 0.5 μs - (-0.5 μs)) over the operating tem- perature range of –40°C to 100°C. ...
Page 14
... Thermal Model for ACPL-P302/W302 Streched-SO6 Pack- age Optocoupler Definitions R : Junction to Ambient Thermal Resistance of LED due 11 to heating of LED R : Junction to Ambient Thermal Resistance of LED due 12 to heating of Detector (Output IC Junction to Ambient Thermal Resistance of Detector 21 (Output IC) due to heating of LED Junction to Ambient Thermal Resistance of Detector 22 (Output IC) due to heating of Detector (Output IC) ...