HCPL-3020 Avago Technologies US Inc., HCPL-3020 Datasheet - Page 14
![no-image](/images/manufacturer_photos/0/0/86/avago_technologies_us_inc__sml.jpg)
HCPL-3020
Manufacturer Part Number
HCPL-3020
Description
OPTOCOUPLER 1CH 0.4A 8-DIP
Manufacturer
Avago Technologies US Inc.
Datasheet
1.HCPL-3020-500.pdf
(15 pages)
Specifications of HCPL-3020
Output Type
Push-Pull, Totem-Pole
Package / Case
8-DIP (0.300", 7.62mm)
Voltage - Isolation
3750Vrms
Number Of Channels
1, Unidirectional
Current - Output / Channel
400mA
Propagation Delay High - Low @ If
200ns @ 7mA
Current - Dc Forward (if)
20mA
Input Type
DC
Mounting Type
Through Hole
Configuration
1 Channel
Isolation Voltage
3750 Vrms
Maximum Propagation Delay Time
700 ns
Maximum Forward Diode Voltage
1.8 V
Minimum Forward Diode Voltage
1.2 V
Maximum Reverse Diode Voltage
5 V
Maximum Forward Diode Current
12 mA
Maximum Power Dissipation
250 mW
Maximum Operating Temperature
+ 100 C
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
HCPL-3020
Manufacturer:
AVAGO
Quantity:
40 000
Part Number:
HCPL-3020
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Company:
Part Number:
HCPL-3020#500
Manufacturer:
PHI
Quantity:
5 510
Company:
Part Number:
HCPL-3020-000E
Manufacturer:
AVAGO
Quantity:
40 000
Part Number:
HCPL-3020-000E
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Company:
Part Number:
HCPL-3020-060
Manufacturer:
AVAGO
Quantity:
40 000
Part Number:
HCPL-3020-060E
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Part Number:
HCPL-3020-300E
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Part Number:
HCPL-3020-360E
Manufacturer:
AVAGO/安华高
Quantity:
20 000
CMR with the LED On (CMR
A high CMR LED drive circuit must keep the LED on during
common mode transients. This is achieved by overdriving
the LED current beyond the input threshold so that it is not
pulled below the threshold during a transient. A minimum
LED current of 7 mA provides adequate margin over the
maximum I
CMR with the LED Off (CMR
A high CMR LED drive circuit must keep the LED off (V
V
during a -dV
ing through C
the logic gate. As long as the low state voltage developed
across the logic gate is less than V
off and no common mode failure will occur.
The open collector drive circuit, shown in Figure 22, cannot
keep the LED off during a +dV
current flowing through C
LED, and it is not recommended for applications requiring
ultra high CMR
which likes the recommended application circuit (Figure
17), does achieve ultra high CMR performance by shunting
the LED in the off state.
14
F(OFF)
) during common mode transients. For example,
FLH
CM
LEDP
1
/dt transient in Figure 21, the current flow-
of 6 mA to achieve 10 kV/µs CMR.
performance. The alternative drive circuit,
also flows through the R
LEDN
H
L
CM
)
)
must be supplied by the
/dt transient, since all the
F(OFF)
the LED will remain
SAT
and V
SAT
of
F
Dead Time and Propagation Delay Specifications
The HCPL-3020 and HCPL-0302 include a Propagation
Delay Difference (PDD) specification intended to help
designers minimize “dead time” in their power inverter
designs. Dead time is the time high and low side power
transistors are off. Any overlap in Ql and Q2 conduction
will result in large currents flowing through the power
devices from the high voltage to the low-voltage motor
rails. To minimize dead time in a given design, the turn
on of LED2 should be delayed (relative to the turn off of
LED1) so that under worst-case conditions, transistor Q1
has just turned off when transistor Q2 turns on, as shown
in Figure 24. The amount of delay necessary to achieve
this condition is equal to the maximum value of the propa-
gation delay difference specification, PDD max, which is
specified to be 500 ns over the operating temperature
range of –40° to 100°C.
Delaying the LED signal by the maximum propagation
delay difference ensures that the minimum dead time is
zero, but it does not tell a designer what the maximum
dead time will be. The maximum dead time is equivalent
to the difference between the maximum and minimum
propagation delay difference specification as shown in
Figure 25. The maximum dead time for the HCPL-3020 and
HCPL-0302 is 1 ms (= 0.5 µs – (–0.5 µs)) over the operating
temperature range of –40°C to 100°C.
Note that the propagation delays used to calculate PDD and dead time are
taken at equal temperatures and test conditions since the optocouplers
under consideration are typically mounted in close proximity to each
other and are switching identical IGBTs.