HCPL-0300-000E Avago Technologies US Inc., HCPL-0300-000E Datasheet - Page 6

• Manufacturer Part Number: HCPL-0300-000E
• Description: OPTOCOUPLER 8MBD LO CURR 8-SOIC
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-0300-000E

• Package / Case: 8-ESOP
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 25mA
• Data Rate: 8MBd
• Propagation Delay High - Low @ If: 110ns @ 625µA
• Current - Dc Forward (if): 5mA
• Input Type: DC
• Output Type: Open Collector
• Mounting Type: Surface Mount
• Isolation Voltage: 3750 Vrms
• Maximum Continuous Output Current: 25 mA
• Maximum Fall Time: 0.02 us
• Maximum Forward Diode Current: 5 mA
• Minimum Forward Diode Voltage: 1 V
• Output Device: Logic Gate Photo IC
• Configuration: 1 Channel
• Maximum Baud Rate: 8 MBd
• Maximum Forward Diode Voltage: 1.5 V
• Maximum Reverse Diode Voltage: 3 V
• Maximum Power Dissipation: 40 mW
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• No. Of Channels: 1
• Optocoupler Output Type: Logic Gate
• Input Current: 1mA
• Output Voltage: 5.25V
• Opto Case Style: SOIC
• No. Of Pins: 8
• Common Mode Ratio: 100
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 516-1626-5

IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (HCPL-2300 Option 060 only)
detailed description.
Note:
Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application.
Absolute Maximum Ratings
(No Derating Required up to 55°C)
Infrared and Vapor Phase Reflow Temperature (Option #300) see Fig. 1, Thermal Profile
*Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section, IEC/EN/DIN EN 60747-5-2, for a
6
Description
Installation classification per DIN VDE 0110/1.89, Table 1
for rated mains voltage ≤300 V rms
for rated mains voltage ≤450 V rms
Climatic Classification
Pollution Degree (DIN VDE 0110/1.89)
Maximum Working Insulation Voltage
Input to Output Test Voltage, Method b*
V
Partial Discharge < 5 pC
Input to Output Test Voltage, Method a*
V
Partial Discharge < 5 pC
Highest Allowable Overvoltage*
(Transient Overvoltage, t
Safety Limiting Values
(Maximum values allowed in the event of a failure,
also see Figure 11, Thermal Derating curve.)
Case Temperature
Input Current
Output Power
Insulation Resistance at TS, VIO = 500 V
Description
Storage Temperature
Operating Temperature
Lead Solder Temperature
(1.6 mm below seating plane)
Average Forward Input Current
Reverse Input Voltage
Supply Voltage
Pull-Up Resistor Voltage
Output Collector Current
Input Power Dissipation
Output Collector Power Dissipation
Output Collector Voltage
IORM
IORM
x 1.875 = V
x 1.5 = V
PR
, Type and sample test, t
PR
, 100% Production Test with t
ini
= 10 sec)
m
= 60 sec,
m
= 1 sec,
Min.
-55°C
-40°C
0 V
-0.5 V
-25 mA
-0.5 V
Typ.
260°C for 10 s
5 mA[2]
10 mW
40 mW
Symbol
V
V
V
V
T
I
P
RS
S,INPUT
S
IORM
PR
PR
IOTM
S,OUTPUT
Max.
+125°C
+85°C
3.0 V
7.0 V
VCC
25 mA
18 V
Characteristic
I-IV
I-III
55/85/21
2
630
1181t
945
6000
175
230
600
≥109
Units
T
T
max
- I
V
V
V
I
P
P
V
Units
V
V
V
V
°C
mA
mW
Ω
O
A
S
R
CC
RL
I
O
O
F
peak
peak
peak
peak