HCPL-7710-300E Avago Technologies US Inc., HCPL-7710-300E Datasheet - Page 17

• Manufacturer Part Number: HCPL-7710-300E
• Description: OPTOCOUPLER CMOS 12MBD GW 8-SMD
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-7710-300E

• Package / Case: 8-SMD Gull Wing
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 10mA
• Data Rate: 12.5MBd
• Propagation Delay High - Low @ If: 20ns
• Input Type: Logic
• Output Type: Push-Pull, Totem-Pole
• Mounting Type: Surface Mount, Gull Wing
• Isolation Voltage: 3750 Vrms
• Maximum Continuous Output Current: 10 mA
• Maximum Fall Time: 0.008 us
• Maximum Forward Diode Current: 10 mA
• Output Device: Logic Gate Photo IC
• Configuration: 1 Channel
• Maximum Baud Rate: 12.5 MBd
• Maximum Power Dissipation: 150 mW
• Maximum Operating Temperature: + 100 C
• Minimum Operating Temperature: - 40 C
• Number Of Elements: 1
• Baud Rate: 12.5Mbps
• Forward Current: 10mA
• Output Current: 10mA
• Package Type: PDIP SMD
• Operating Temp Range: -40C to 100C
• Power Dissipation: 150mW
• Propagation Delay Time: 40ns
• Pin Count: 8
• Mounting: Surface Mount
• Operating Temperature Classification: Industrial
• No. Of Channels: 1
• Optocoupler Output Type: Gate Drive
• Input Current: 10µA
• Output Voltage: 5V
• Opto Case Style: SMD
• No. Of Pins: 8
• Common Mode Ratio: 10000
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 516-1688-5

17
Power Supplies and Bypassing
The recommended PROFIBUS application circuit is
shown in Figure 24. Since the HCPL-x710 are fully com-
patible with CMOS logic level signals, the o p to co up -
ler is connected directly to the transceiver. Two bypass
capacitors (with values between 0.01 and 0.1 µF) are
required and should be located as close as possible to
the input and output power-supply pins of the HCPL-
x710. For each capacitor, the total lead length between
both ends of the capacitor and the power supply pins
should not exceed 20 mm. The bypass capacitors are
required because of the high-speed digital nature of the
signals inside the optocoupler.
Figure 24. Recommended PROFIBUS application circuit.
Tx ENABLE
Rx
Tx
0.01 µF
0.01 µF
1, 0 kΩ
5 V
5 V
5 V
8
7
6
5
1
2
3
4
1
2
3
4
V
V
GND
V
V
GND
ANODE
CATHODE
DD2
O
DD1
IN
BOUNDARY
HCPL-061N
ISOLATION
HCPL-x710
HCPL-x710
GALVANIC
2
1
GND
GND
GND
V
V
V
V
CC
V
DD1
DD2
V
V
O
E
IN
O
1
2
8
7
6
5
1
2
3
4
8
7
6
5
ISO 5 V
0.01
ISO 5 V
ISO 5 V
µF
HCPL-0710 fig 23
0.01
0.01
µF
µF
680 Ω
0.01
µF
Being very similar to multi-station RS485 systems, the
HCPL-061N optocoupler provides a transmit disable
function which is necessary to make the bus free after
each master/slave transmission cycle. Specifically, the
HCPL-061N disables the transmitter of the line driver
by putting it into a high state mode. In addition, the
HCPL-061N switches the RX/TX driver IC into the listen
mode. The HCPL-061N offers HCMOS compatibility and
the high CMR performance (1 kV/µs at V
essential in industrial communication interfaces.
1
4
3
2
R
D
DE
RE
SN75176B
ISO 5 V
GND
V
CC
8
5
A
B
6
7
0.01 µF
RT
+
SHIELD
–
1 M
CM
= 1000 V)