HCPL-073L-000E Avago Technologies US Inc., HCPL-073L-000E Datasheet - Page 10

• Manufacturer Part Number: HCPL-073L-000E
• Description: OPTOCOUPLER 2CHAN 3.3V 8-SOIC
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-073L-000E

• Input Type: DC
• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 2, Unidirectional
• Current - Output / Channel: 60mA
• Data Rate: 100KBd
• Propagation Delay High - Low @ If: 30µs @ 500µA
• Current - Dc Forward (if): 20mA
• Output Type: Open Collector
• Mounting Type: Surface Mount
• Isolation Voltage: 3750 Vrms
• Output Device: Darlington With Base
• Configuration: 2 Channel
• Current Transfer Ratio: 5000 %
• Maximum Baud Rate: 100 KBps
• Maximum Forward Diode Voltage: 1.7 V
• Maximum Reverse Diode Voltage: 5 V
• Maximum Input Diode Current: 20 mA
• Maximum Power Dissipation: 135 mW
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 516-1644-5

Package Characteristics
Parameter
Input-Output
Momentary
Withstand
Voltage**
Resistance
(Input-Output)
Capacitance
(Input-Output)
Input-Input
Insulation
Leakage Current
Input-Input
Insulation
Leakage Current
Capacitance
(Input-Input)
*All typical values at TA = 25˚C, unless otherwise noted.
**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equip-
ment level safety specification or Avago Application Note 1074 entitled "Optocoupler Input-Output Endurance Voltage."
Notes:
1. Pin 5 should be the most negative voltage at the detector side.
2. Each channel.
3. DC CURRENT TRANSFER RATIO (CTR) is defined as the ratio of output collector current, I
4. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together, and pins 5, 6, 7, and 8 shorted together.
5. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together.
6. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dV
7. In applications where dV/dt may exceed 50,000 V/µs (such as static discharge) a series resistor, R
8. Use of a 0.1 µF bypass capacitor connected between pins 5 and 8 adjacent to the device is recommended.
9. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 4500 V rms for 1 second (leakage detec-
10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 6000 V rms for 1 second (leakage detec-
11. Measured between the LED anode and cathode shorted together and pins 5 through 8 shorted together.
12. Derate linearly above 65˚C free-air temperature at a rate of 2.3 mW/˚C for the SO-8 package.
10
sure that the output will remain in a Logic High state (i.e., V
maximum tolerable (negative) dV
(i.e., V
IC from destructively high surge currents. The recommended value is R
tion current limit, I
tion current limit, I
O
< 0.8 V).
I-O
I-O
< 5 µA).
< 5 µA).
Sym.
V
R
C
I
R
C
I-I
ISO
I-O
I-O
I-I
I-I
Device HCPL-
270L
273L
070L
073L
CM
/dt of the common mode pulse, V
Min.
3750
0.005
O
Typ.*
10
0.6
10
0.03
0.25
> 2.0 V). Common mode transient immunity in a Logic Low level is the
12
11
Max.
CM
CC
, to assure that the output will remain in a Logic Low state
= 110 Ω.
Units
V rms
Ω
pF
µA
Ω
pF
O
, to the forward LED input current, I
Test Conditions
RH ≤ 50%,
t = 1 min.,
T
V
RH ≤ 45%
f = 1 MHz
RH ≤ 45%
V
A
CM
I-O
I-I
CC
= 25˚C
, should be included to protect the detector
= 500 Vdc
/dt of the common mode pulse, V
= 500 Vdc
Fig.
F
, times 100%.
Note
4, 9
4
11
5
5
5
CM
, to as-