SI8410BD-A-IS Silicon Laboratories Inc, SI8410BD-A-IS Datasheet - Page 15

• Manufacturer Part Number: SI8410BD-A-IS
• Description: ISOLATOR 1CH 5KV 150M 16SOIC
• Manufacturer: Silicon Laboratories Inc
• Series: ISOpror

Specifications of SI8410BD-A-IS

• Number Of Channels: 1
• Package / Case: 16-SOIC (0.300", 7.5mm Width)
• Inputs - Side 1/side 2: 1/0
• Isolation Rating: 5000Vrms
• Voltage - Supply: 2.7 V ~ 5.5 V
• Data Rate: 150Mbps
• Propagation Delay: 6ns
• Output Type: Logic
• Operating Temperature: -40°C ~ 125°C
• Mounting Style: SMD/SMT
• Propagation Delay Time: 9.5 ns
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Supply Current: 1.8 mA
• Power Dissipation: 150 mW
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 336-1932-5; SI8410BD-A-IS

Table 3. Electrical Characteristics
(V
Table 4. Absolute Maximum Ratings
Parameter
All Models
Output Rise Time
Output Fall Time
Peak Eye Diagram Jitter
Common Mode Transient
Immunity
Start-up Time
Notes:
Parameter
Storage Temperature
Operating Temperature
Supply Voltage
Input Voltage
Output Voltage
Output Current Drive Channel
Lead Solder Temperature (10 s)
Maximum Isolation Voltage (1 s) NB SOIC-8
Maximum Isolation Voltage (1 s) WB SOIC-16
Notes:
DD1
1. Specifications in this table are also valid at VDD1 = 2.6 V and VDD2 = 2.6 V when the operating temperature range is
2. The nominal output impedance of an isolator driver channel is approximately 50 , ±40%, which is a combination of the
3. t
4. Start-up time is the time period from the application of power to valid data at the output.
1. Permanent device damage may occur if the above absolute maximum ratings are exceeded. Functional operation
2. VDE certifies storage temperature from –40 to 150 °C.
= 2.70 V, V
constrained to T
value of the on-chip series termination resistor and channel resistance of the output driver FET. When driving loads
where transmission line effects will be a factor, output pins should be appropriately terminated with controlled
impedance PCB traces.
the same supply voltages, load, and ambient temperature.
should be restricted to conditions as specified in the operational sections of this data sheet.
PSK(P-P)
4
is the magnitude of the difference in propagation delay times measured between different units operating at
DD2
= 2.70 V, T
A
2
= 0 to 85 °C.
A
= –40 to 125 °C)
Symbol
t
CMTI
JIT(PK)
t
1
SU
t
t
r
f
(Continued)
1
Test Condition
V
See Figure 6
I
C
C
= V
L
L
Rev. 1.0
= 15 pF
= 15 pF
DD
or 0 V
V
DD1
Symbol
T
Si8422/23 (2.5 & 5 kV)
V
STG
T
V
I
, V
O
A
O
I
DD2
Si8410/20/21 (5 kV)
Min
20
—
—
—
—
–0.5
–0.5
–0.5
Min
–65
–40
—
—
—
—
Typ
Typ
350
2.0
2.0
—
—
—
—
—
—
—
—
—
45
15
V
V
DD
DD
4500
6500
Max
Max
150
125
260
6.0
10
4.0
4.0
40
—
—
+ 0.5
+ 0.5
V
V
kV/µs
Unit
Unit
mA
C°
C°
C°
RMS
RMS
µs
ns
ns
ps
V
V
V
15