SI8422BD-B-IS Silicon Laboratories Inc, SI8422BD-B-IS Datasheet - Page 24
![no-image](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_sml.jpg)
SI8422BD-B-IS
Manufacturer Part Number
SI8422BD-B-IS
Description
ISOLATOR 2CH 5KV 150M 16SOIC
Manufacturer
Silicon Laboratories Inc
Series
ISOpror
Datasheet
1.SI8422AD-B-IS.pdf
(38 pages)
Specifications of SI8422BD-B-IS
Number Of Channels
2
Package / Case
16-SOIC (0.300", 7.5mm Width)
Inputs - Side 1/side 2
1/1
Isolation Rating
5000Vrms
Voltage - Supply
2.7 V ~ 5.5 V
Data Rate
150Mbps
Propagation Delay
8ns
Output Type
Logic
Operating Temperature
-40°C ~ 125°C
Mounting Style
SMD/SMT
Propagation Delay Time
9.5 ns
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.7 V
Power Dissipation
150 mW
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
336-1938-5
SI8422BD-B-IS
SI8422BD-B-IS
Si8410/20/21 (5 kV)
Si 8422/23 (2. 5 & 5 kV)
3.3. Layout Recommendations
To ensure safety in the end user application, high voltage circuits (i.e., circuits with >30 V
) must be physically
AC
separated from the safety extra-low voltage circuits (SELV is a circuit with <30 V
) by a certain distance
AC
(creepage/clearance). If a component, such as a digital isolator, straddles this isolation barrier, it must meet those
creepage/clearance requirements and also provide a sufficiently large high-voltage breakdown protection rating
(commonly referred to as working voltage protection). Table 6 on page 16 and Table 7 on page 17 detail the
working voltage and creepage/clearance capabilities of the Si84xx. These tables also detail the component
standards (UL1577, IEC60747, CSA 5A), which are readily accepted by certification bodies to provide proof for
end-system specifications requirements. Refer to the end-system specification (61010-1, 60950-1, 60601-1, etc.)
requirements before starting any design that uses a digital isolator.
3.3.1. Supply Bypass
The Si841x/2x family requires a 0.1 µF bypass capacitor between V
and GND1 and V
and GND2. The
DD1
DD2
capacitor should be placed as close as possible to the package. To enhance the robustness of a design, it is further
recommended that the user also add 1 µF bypass capacitors and include 100 resistors in series with the inputs
and outputs if the system is excessively noisy.
3.3.2. Pin Connections
No connect pins are not internally connected. They can be left floating, tied to
, or tied to GND.
V
DD
3.3.3. Output Pin Termination
The nominal output impedance of an isolator driver channel is approximately 50 , ±40%, which is a combination
of the value of the on-chip series termination resistor and channel resistance of the output driver FET. When driving
loads where transmission line effects will be a factor, output pins should be appropriately terminated with controlled
impedance PCB traces.
3.4. Fail-Safe Operating Mode
Si84xx devices feature a selectable (by ordering option) mode whereby the default output state (when the input
supply is unpowered) can either be a logic high or logic low when the output supply is powered. See Table 12 on
page 22 and "6. Ordering Guide" on page 29 for more information.
24
Rev. 1.0