KSZ8995MA Micrel Inc, KSZ8995MA Datasheet - Page 43

• Manufacturer Part Number: KSZ8995MA
• Description: IC SWITCH 10/100 5PORT 128PQFP
• Manufacturer: Micrel Inc

Specifications of KSZ8995MA

• Data Rate: 100Mbps
• Applications: *
• Mounting Type: Surface Mount
• Package / Case: 128-MQFP, 128-PQFP
• No. Of Ports: 5
• Ethernet Type: IEEE 802.3u
• Supply Voltage Range: 1.7V To 1.9V, 3.15V To 3.45V
• Operating Temperature Range: 0°C To +70°C
• Digital Ic Case Style: QFP
• No. Of Pins: 128
• Number Of Primary Switch Ports: 5
• Internal Memory Buffer Size: 64
• Operating Supply Voltage (typ): 1.8/2.5/3.3V
• Fiber Support: Yes
• Integrated Led Drivers: Yes
• Phy/transceiver Interface: MII/SNI
• Power Supply Type: Analog/Digital
• Package Type: PQFP
• Data Rate (typ): 10/100Mbps
• Vlan Support: Yes
• Operating Temperature (max): 70C
• Operating Temperature (min): 0C
• Pin Count: 128
• Mounting: Surface Mount
• Jtag Support: No
• Operating Temperature Classification: Commercial
• Interface Type: MII, SNI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 576-1607 - BOARD EVAL EXPERIMENT KSZ8995MA
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant
• Other names: 576-1039

Semptember 2008
Global Registers
Address
Register 0 (0x00): Chip ID0
7-0
Register 1 (0x01): Chip ID1 / Start Switch
7-4
3-1
0
Register 2 (0x02): Global Control 0
7
6-4
3
2
1
0
Register 3 (0x03): Global Control 1
7
6
Name
family ID
Chip ID
Revision ID
Start Switch
Reserved
802.1p Base Priority
Enable PHY MII
Buffer Share Mode
UNH Mode
Link Change Age
Pass All Frames
Reserved
Description
Chip family.
0x0 is assigned to M series. (95MA)
Revision ID
1, start the chip when external pins (PS1, PS0) = (1,0) or
(0,1). Note: in (PS1,PS0) = (0,0) mode, the chip will
start automatically, after trying to read the external
EEPROM. If EEPROM does not exist, the chip will use
default values for all internal registers. If EEPROM is
present, the contents in the EEPROM will be checked.
The switch will check: (1) Register 0 = 0x95,
(2) Register 1 [7:4] = 0x0. If this check is OK, the
contents in the EEPROM will override chip register
default values =0, chip will not start when external pins
(PS1, PS0) = (1,0) or (0,1).
Note: (PS1, PS0) = (1,1) for Factory test only.
Reserved.
Used to classify priority for incoming 802.1q packets
“User priority” is compared against this value ⊕ :
classified as high priority. < : classified as low priority.
1, enable PHY MII-P5 interface.
Note: if not enabled, the switch will tri-state all outputs.
1, buffer pool is shared by all ports. A port can use more
buffer when other ports are not busy.
0, a port is only allowed to use 1/5 of the buffer pool.
1, the switch will drop packets with 0x8808 in T/L filed, or
DA=01-80-C2-00-00-01.
0, the switch will drop packets qualified as “flow control”
packets.
1, link change from “link” to “no link” will cause fast aging
(<800µs) to age address table faster. After an age cycle
is complete, the age logic will return to normal (300 + 75
seconds ). Note: If any port is
unplugged, all addresses will be automatically aged out.
1, switch all packets including bad ones. Used solely for
debugging purpose. Works in conjunction with
sniffer mode.
Reserved.
43
Mode
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
RW
RO
RO
RO
Based on real chip
revision. 0x02=B2,
0x03=B3,
0x04=B4,
0x05=B5, etc.
Pin LED5-1 strap
option.
Pull-down (0):
isolate. Pull-up
(1): Enable.
Note: LED[5][1]
has internal pull-
up.
M9999-091508
Default
0x95
0x0
0x0
0x0
0x4
0x1
0
0
0
0