NCP1411DMR2G ON Semiconductor, NCP1411DMR2G Datasheet
NCP1411DMR2G
Specifications of NCP1411DMR2G
Available stocks
Related parts for NCP1411DMR2G
NCP1411DMR2G Summary of contents
Page 1
... ORDERING INFORMATION Device Package Shipping† NCP1411DMR2 Micro8 4000 Tape & Reel NCP1411DMR2G Micro8 4000 Tape & Reel (Pb−Free) †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. ...
Page 2
Input OUT 220 pF 200 k Low Battery Sense Input R LB1 Shutdown Open Drain C Input EN 120 nF Low Battery Open Drain Output Á Á Á Á Á Á Á Á Á Á Á ...
Page 3
ELECTRICAL CHARACTERISTICS unless otherwise noted.) Characteristic Operating Input Voltage Output Voltage Range (Adjusted by external feedback) Reference Voltage (C = 150 nF, under no loading, T REF Reference Voltage (C = 150 nF, under no loading, −40°C ≤ T REF ...
Page 4
ZLC Chip Enable − PFM REF Voltage Reference 4 + LBI/EN − − CONTROL LOGIC V _ZCUR DD _MSON _MAINSW2ON _PWQONCE GND _CEN _PFM _MAINSWOFD _SYNSW2ON _SYNSWOFD _V REFOK _ILIM + − ...
Page 5
TYPICAL OPERATING CHARACTERISTICS 1.220 V = 3.3 V OUT 1.215 1 OUT 1.210 REF T = 25°C A 1.205 ...
Page 6
1 3.3 V OUT OUT ...
Page 7
3.3 V OUT −2 OUT −3 100 I , OUTPUT LOADING CURRENT (mA) LOAD Figure 15. Output Voltage ...
Page 8
3 100 mA mH, IN OUT LOAD mF) OUT Upper Trace: Voltage at L pin, 2.0 V/Division X MiddleTrace: Output Voltage Ripple, 50 mV/Division Lower ...
Page 9
DETAILED OPERATION DESCRIPTIONS NCP1411 is a monolithic micropower high frequency step−up voltage switching converter IC specially designed for battery operated hand−held electronic products up to 250 mA loading. It integrates Synchronous Rectifier for improving efficiency as well as eliminating the ...
Page 10
V, the IC will be enabled. The internal circuit will only consume 9.0 mA current typically from the OUT pin. In order to ensure proper startup, a timing capacitor C as shown in ...
Page 11
Feedback signal path must be separated with the main current path and sensing directly at the anode of the output capacitor. Components Placement Power components, i.e. input capacitor, inductor and output capacitor, must be placed as close ...
Page 12
GENERAL DESIGN PROCEDURES Switching mode converter design is considered as black magic to most engineers, some complicate empirical formulae are available for reference usage. Those formulae are derived from the assumption that the key components, i.e. power inductor and capacitors ...
Page 13
... C 0.038 (0.0015) H 1.04 8X 0.041 6X 0.0256 *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. PACKAGE DIMENSIONS Micro8 DM SUFFIX CASE 846A−02 ISSUE F NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI 2. CONTROLLING DIMENSION: MILLIMETER. ...
Page 14
... Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303− ...