LM2576T-005 ON Semiconductor, LM2576T-005 Datasheet - Page 16
![IC REG SW 3A 5V STEPDOWN TO220-5](/photos/36/39/363974/to220-5_sml.jpg)
LM2576T-005
Manufacturer Part Number
LM2576T-005
Description
IC REG SW 3A 5V STEPDOWN TO220-5
Manufacturer
ON Semiconductor
Type
Step-Down (Buck)r
Datasheet
1.LM2576D2T-ADJR4G.pdf
(28 pages)
Specifications of LM2576T-005
Internal Switch(s)
Yes
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
5V
Current - Output
3A
Frequency - Switching
52kHz
Voltage - Input
7 ~ 40 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Through Hole
Package / Case
TO-220-5 (Straight Leads)
Mounting Style
Through Hole
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Power - Output
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
LM2576T-005OS
LM2576T-5
LM2576T-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LM2576T-005G
Manufacturer:
ON Semiconductor
Quantity:
1 982
Catch Diode
Locate the Catch Diode Close to the LM2576
fast diode to provide a return path for the inductor current
when the switch turns off. This diode must be located close
to the LM2576 using short leads and short printed circuit
traces to avoid EMI problems.
Use a Schottky or a Soft Switching
Ultra−Fast Recovery Diode
losses within switching power supplies, choosing the
rectifier that best fits into the converter design is an
important process. Schottky diodes provide the best
performance because of their fast switching speed and low
forward voltage drop.
voltage applications (5.0 V and lower). Another choice
could be Fast−Recovery, or Ultra−Fast Recovery diodes. It
has to be noted, that some types of these diodes with an
abrupt turnoff characteristic may cause instability or
EMI troubles.
can better fulfill some quality, low noise design requirements.
Table 1 provides a list of suitable diodes for the LM2576
regulator. Standard 50/60 Hz rectifier diodes, such as the
1N4001 series or 1N5400 series are NOT suitable.
Inductor
switching power supply designs. The style of the core and
the winding technique used in the magnetic component’s
design has a great influence on the reliability of the overall
power supply.
high voltage spikes generated by the rate of transitions in
current within the switching power supply, and the
possibility of core saturation can arise during an abnormal
operational mode. Voltage spikes can cause the
semiconductors to enter avalanche breakdown and the part
can instantly fail if enough energy is applied. It can also
cause significant RFI (Radio Frequency Interference) and
EMI (Electro−Magnetic Interference) problems.
Continuous and Discontinuous Mode of Operation
continuous and the discontinuous modes of operation. The
regulator works in the continuous mode when loads are
relatively heavy, the current flows through the inductor
continuously and never falls to zero. Under light load
conditions, the circuit will be forced to the discontinuous
mode when inductor current falls to zero for certain period
of time (see Figure 23 and Figure 24). Each mode has
distinctively different operating characteristics, which can
affect the regulator performance and requirements. In many
cases the preferred mode of operation is the continuous
mode. It offers greater output power, lower peak currents in
the switch, inductor and diode, and can have a lower output
The LM2576 is a step−down buck converter; it requires a
Since the rectifier diodes are very significant sources of
They provide the best efficiency especially in low output
A fast−recovery diode with soft recovery characteristics
The magnetic components are the cornerstone of all
Using an improper or poorly designed inductor can cause
The LM2576 step−down converter can operate in both the
http://onsemi.com
LM2576
16
ripple voltage. On the other hand it does require larger
inductor values to keep the inductor current flowing
continuously, especially at low output load currents and/or
high input voltages.
selection guide for the LM2576 regulator was added to this
data sheet (Figures 18 through 22). This guide assumes that
the regulator is operating in the continuous mode, and
selects an inductor that will allow a peak−to−peak inductor
ripple current to be a certain percentage of the maximum
design load current. This percentage is allowed to change as
different design load currents are selected. For light loads
(less than approximately 300 mA) it may be desirable to
operate the regulator in the discontinuous mode, because the
inductor value and size can be kept relatively low.
Consequently, the percentage of inductor peak−to−peak
current increases. This discontinuous mode of operation is
perfectly acceptable for this type of switching converter.
Any buck regulator will be forced to enter discontinuous
mode if the load current is light enough.
Selecting the Right Inductor Style
are core material, cost, the output power of the power supply,
the physical volume the inductor must fit within, and the
amount of EMI (Electro−Magnetic Interference) shielding
that the core must provide. The inductor selection guide
covers different styles of inductors, such as pot core, E−core,
toroid and bobbin core, as well as different core materials
such as ferrites and powdered iron from different
manufacturers.
be the best choice. Since the magnetic flux is contained
within the core, it generates less EMI, reducing noise
problems in sensitive circuits. The least expensive is the
bobbin core type, which consists of wire wound on a ferrite
rod core. This type of inductor generates more EMI due to
the fact that its core is open, and the magnetic flux is not
contained within the core.
Waveform
Waveform
To simplify the inductor selection process, an inductor
Some important considerations when selecting a core type
For high quality design regulators the toroid core seems to
Inductor
Current
Current
Switch
Power
Figure 23. Continuous Mode Switching Current
2.0 A
2.0 A
0 A
0 A
HORIZONTAL TIME BASE: 5.0 ms/DIV
Waveforms