LM2596DSADJG ON Semiconductor, LM2596DSADJG Datasheet - Page 20

• Manufacturer Part Number: LM2596DSADJG
• Description: IC REG SW STP-DWN 3A D2PAK-5
• Manufacturer: ON Semiconductor
• Type: Step-Down (Buck)r

Specifications of LM2596DSADJG

• Internal Switch(s): Yes
• Synchronous Rectifier: No
• Number Of Outputs: 1
• Voltage - Output: 1.23 ~ 37 V
• Current - Output: 3A
• Frequency - Switching: 150kHz
• Voltage - Input: 4.5 ~ 40 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: D²Pak, TO-263 (5 leads + tab)
• Output Voltage: 1.23 V to 37 V
• Output Current: 3 A
• Input Voltage: 4.5 V to 40 V
• Switching Frequency: 150 KHz
• Operating Temperature Range: - 40 C to + 125 C
• Mounting Style: SMD/SMT
• Duty Cycle (max): 95 %
• Isolated/non-isolated: Non Isolated
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power - Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Delayed Startup
already mentioned above, which require a higher amount of
startup current. In such cases, if the input power source is
limited, this delayed startup feature becomes very useful.
voltage is applied and the time when the output voltage
comes up, the circuit in Figure 27 can be used. As the input
voltage is applied, the capacitor C1 charges up, and the
voltage across the resistor R2 falls down. When the voltage
on the ON/OFF pin falls below the threshold value 1.3 V, the
regulator starts up. Resistor R1 is included to limit the
maximum voltage applied to the ON/OFF pin. It reduces the
power supply noise sensitivity, and also limits the capacitor
C1 discharge current, but its use is not mandatory.
respectively) ripple voltage exists, a long delay time can
cause some problems by coupling the ripple into the
ON/OFF pin, the regulator could be switched periodically
on and off with the line (or double) frequency.
Undervoltage Lockout
the input voltage reaches a certain threshold level. Figure 28
shows an undervoltage lockout circuit applied to a buck
regulator. A version of this circuit for buck−boost converter
is shown in Figure 29. Resistor R3 pulls the ON/OFF pin
high and keeps the regulator off until the input voltage
reaches a predetermined threshold level with respect to the
ground Pin 3, which is determined by the following
expression:
There are some applications, like the inverting regulator
To provide a time delay between the time when the input
When a high 50 Hz or 60 Hz (100 Hz or 120 Hz
Some applications require the regulator to remain off until
NOTE: This picture does not show the complete circuit.
100 mF
+V
Figure 27. Delayed Startup Circuitry
in
V
C
in
th
[ V
Z1
) 1.0 ) R2
C1
0.1 mF
47 k
R1
+V
in
1
R1
5
LM2596−XX
ON/OFF
R2
47 k
V
BE
( Q1 )
3
GN
D
http://onsemi.com
20
current:
conditions, the worst case occurs when V
Adjustable Output, Low−Ripple Power Supply
features an adjustable output voltage is shown in Figure 30.
The input voltage ranges from roughly 3.0 V to 40 V. In order
to achieve a 10 or more times reduction of output ripple, an
additional L−C filter is included in this circuit.
where t on +
The following formula is used to obtain the peak inductor
Under normal continuous inductor current operating
A 3.0 A output current capability power supply that
This regulator delivers 3.0 A into 1.2 V to 35 V output.
1N5242B
1N5242B
NOTE: This picture does not show the complete circuit.
NOTE: This picture does not show the complete circuit.
Figure 28. Undervoltage Lockout Circuit for
+V
Figure 29. Undervoltage Lockout Circuit for
15 k
15 k
I
R2
Z1
R1
+V
in
10 k
10 k
peak
R2
Z1
R1
in
47 k
[
V
R3
47 k
in
R3
Buck−Boost Converter
I
Load
|V
Q1
2N3904
) |V
Buck Converter
Q1
2N3904
O
|
(V
O
V
in
|
C
100 mF
in
+V
x 1.0
in
C
100 mF
) |V
+V
in
in
f osc
1
in
1
5
O
, and f osc + 52 kHz.
LM2596−XX
5
|)
ON/OFF
LM2596−XX
V
)
ON/OFF
th
≈ 13 V
in
V
is minimal.
in
3
2L 1
x t on
3
GN
D
V
GN
D
th
≈ 13 V
V
out