LTC1266IS-5#TRPBF Linear Technology, LTC1266IS-5#TRPBF Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/3/388/linear_technology_sml.jpg)
LTC1266IS-5#TRPBF
Manufacturer Part Number
LTC1266IS-5#TRPBF
Description
IC REG CNTRLR N/PCH MOSFET16SOIC
Manufacturer
Linear Technology
Type
Step-Down (Buck), Step-Up (Boost)r
Datasheet
1.LTC1266CSPBF.pdf
(20 pages)
Specifications of LTC1266IS-5#TRPBF
Internal Switch(s)
No
Synchronous Rectifier
Yes
Number Of Outputs
1
Voltage - Output
5V
Current - Output
50mA
Frequency - Switching
400kHz
Voltage - Input
3.5 ~ 18 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
16-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power - Output
-
OPERATIO
APPLICATIO S I FOR ATIO
LTC1266
LTC1266-3.3/LTC1266-5
When the voltage on the timing capacitor has discharged
past V
causes the bottom-side output to switch off and the
topside output to switch on (ground for P-channel and
Power V
As the load current increases, the output voltage decreases
slightly. This causes the output of the gain stage (Pin 7) to
increase the current comparator threshold, thus tracking
the load current.
The sequence of events for Burst Mode operation is very
similar to continuous operation with the cycle interrupted
by the voltage comparator. When the output voltage is at
or above the desired regulated value, the topside MOSFET
is held off by comparator V and the timing capacitor
continues to discharge below V
capacitor discharges past V
trips, causing the internal sleep line to go low and the
bottom-side MOSFET to turn off.
The circuit now enters sleep mode with both power
MOSFETs turned off. In sleep mode, a majority of the
circuitry is turned off, dropping the quiescent current
from 2.1mA to 170 A. The load current is now being
supplied from the output capacitor. When the output
voltage has dropped by the amount of hysteresis in
comparator V, the topside MOSFET is again turned on
and this process repeats.
To avoid the operation of the current loop interfering with
Burst Mode operation, a built-in offset V
in the gain stage. This prevents the current comparator
threshold from increasing until the output voltage has
dropped below a minimum threshold.
One of the three basic LTC1266 application circuits is
shown in Figure 1. This circuit uses an N-channel
topside driver and a single supply. The other two circuit
configurations (see Typical Applications) use an
N-channel topside driver and dual supply, and a
P-channel topside driver. Selections of other external
components are driven by the load requirement and are
the same for all three circuit configurations. The first
8
TH1
IN
, comparator T trips, setting the flip-flop. This
for N-channel). The cycle then repeats.
U
U
U
TH2
, voltage comparator S
TH1
W
. When the timing
OS
is incorporated
U
To prevent both the external MOSFETs from ever being
turned on at the same time, feedback is incorporated to
sense the state of the driver output pins. Before the
bottom-side drive output can turn on, the topside output
must be off. Likewise, the topside output is prevented
from turning on while the bottom-side drive output is
still on.
The LTC1266 has two select pins which provide the user
with choice of topside switch and with the option of
inhibiting Burst Mode operation. The phase select pin
allows the user to choose whether the topside MOSFET
is a P-channel or an N-channel. The phase select pin does
two things: sets the proper phase of the drive signal (ON
= Power V
and also sets an upper limit for the on-time (60 s) when
set to the N-channel. The on-time limit ensures proper
start-up when used in a single supply bootstrap circuit
configuration (see Applications Information). In P-channel
mode there is no on-time limit and thus, in dropout, the
P-channel MOSFET is turned on continuously (100%
duty cycle).
The Burst Mode operation inhibit (BINH, Pin 4) allows the
Burst Mode operation to be disabled by applying a CMOS
logic high to this pin. With Burst Mode operation disabled,
the LTC1266 will remain in continuous mode down to zero
load. Burst Mode operation is disabled by allowing the
lower current threshold limit to go below zero so that the
voltage comparator will never trip. The voltage comparator
trip point is also raised up so that it will not be tripped by
transients. It is still active to provide a voltage clamp to
prevent the output from overshooting.
step is the selection of R
C
D1 are selected. Finally, C
the loop is compensated. Using an N-channel topside
switch, input voltages are limited to a maximum of
about 15V. With a P-channel, the input voltage may be
as high as 20V.
T
and L can be chosen. Next, the power MOSFETs and
IN
for N-channel and ON = 0V for P-channel)
SENSE
IN
and C
. Once R
OUT
are selected and
SENSE
is known,