LTC3458LEDE#PBF Linear Technology, LTC3458LEDE#PBF Datasheet
LTC3458LEDE#PBF
Specifications of LTC3458LEDE#PBF
Available stocks
Related parts for LTC3458LEDE#PBF
LTC3458LEDE#PBF Summary of contents
Page 1
... The LTC3458L is available in a low profile (0.75mm), 4mm × 3mm 12-pin DFN package. , LT, LTC and LTM are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Burst Mode is a registered trademark of Linear Technology Corporation. Protected by U.S. Patents including 5481178, 6580258, 6304066, 6127815, 6498466, 6611131 ...
Page 2
... Pulsed <100ns ........................................ –0. ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL LTC3458LEDE#PBF LTC3458LEDE#TRPBF Consult LTC Marketing for parts specified with wider operating temperature ranges. Consult LTC for information on nonstandard lead based finish parts. For more information on lead free part marking, go to: ...
Page 3
ELECTRICAL CHARACTERISTICS temperature range, otherwise specifications are at T PARAMETER Error Amplifier Sink Current SYNC Input High SYNC Input Low SHDN Input High SHDN Input Low BURST Mode Peak Current (I ) BURSTPEAK BURST Threshold Voltage Note 1: Stresses beyond ...
Page 4
LTC3458L W U TYPICAL PERFOR A CE CHARACTERISTICS Frequency Accuracy 1. 200k 1.03 1.01 0.99 0.97 0.95 –45 –30 – TEMPERATURE (°C) 3458L G07 Maximum Load Current 1600 1.8 to 5.5V ...
Page 5
W U TYPICAL PERFOR A CE CHARACTERISTICS Fixed Frequency (FF) Discontinuous Current SW 1V/DIV I L 100mA/DIV V = 3.3V 500ns/DIV OUT L = 7.4μH Over-Current with 2A I LIMIT I L 0.5A/DIV SW 2V/DIV V ...
Page 6
LTC3458L W U TYPICAL PERFOR A CE CHARACTERISTICS Sync Operation at 1.33MHz SW 5V/DIV SYNC 2V/DIV I L 200mA/DIV 500ns/DIV OUT R = 200k T Burst Mode Operation 10mA to 50mA Load Step ...
Page 7
CTIO S SW (Pin 1): Switch Pin for Inductor Connection. During discontinuous conduction mode an antiring resistor con- nects reduce noise (Pin 2): Input Supply Pin. Connect this to ...
Page 8
LTC3458L W BLOCK DIAGRA V IN OSC/SYNC SYNC SLOPE 3 MAX R 6 DUTY T I ZERO P-DRIVE PWM AND BURST MODE N-DRIVE DRIVE LOGIC SLEEP CONTROL MODE I FIXED COMP/LIMIT_PEAK FREQUENCY I BURST_PEAK BURST MODE MUX V PGND 9 ...
Page 9
U U APPLICATIO S I FOR ATIO Error Amp. The error amplifier is a transconductance type, with its positive input internally connected to the 1.225V reference, and its negative input connected to FB. A simple compensation network is placed from ...
Page 10
LTC3458L U U APPLICATIO S I FOR ATIO transition occurs using a single resistor. During Burst Mode operation, the oscillator is shut down, since the on time is determined by the time it takes the inductor current to reach a ...
Page 11
U U APPLICATIO S I FOR ATIO COMPONENT SELECTION Inductor Selection The high frequency operation of the LTC3458L allows for the use of small surface mount inductors. Since the internal slope compensation circuit relies on the inductor’s current slope and ...
Page 12
LTC3458L U U APPLICATIO S I FOR ATIO Input Capacitor Selection The input filter capacitor reduces peak currents drawn from the input source and reduces input switching noise. In most applications >1μF per amp of peak input current is recommended. ...
Page 13
U U APPLICATIO S I FOR ATIO The typical error amp compensation is shown in Figure 2. The equations for the loop dynamics are as follows: 1 ≈ f which is close to DC POLE 1 π • ...
Page 14
LTC3458L U TYPICAL APPLICATIO S Lithium-Ion to 5V, 750mA at 750kHz COILCRAFT 10μH MSS7341 V IN Li-Ion LTC3458L 2.2μF 3.1V to 4.2V V GND/PGND SHDN ON OFF COMP SYNC R T BURST I LIM 274k 84.5k Two Cell to 5V ...
Page 15
... MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 4. EXPOSED PAD SHALL BE SOLDER PLATED Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. U DE/UE Package 12-Lead Plastic DFN (4mm × ...
Page 16
... OUT(MAX) = 10V 10μA, ThinSOT OUT(MAX 36V 2mA, I < 1μA, SC70, OUT(MAX 34V 25μA, I < 1μA, OUT(MAX 0807 REV A • PRINTED IN USA © LINEAR TECHNOLOGY CORPORATION 2005 3.3 3458L TA06b < 1μA, < 1μA, MS8 < 1μA, < 1μA, < 1μA, 3458lfa ...