MAX15035ETL+ Maxim Integrated Products, MAX15035ETL+ Datasheet - Page 11

• Manufacturer Part Number: MAX15035ETL+
• Description: IC REG STEP DOWN 15A 40-TQFN
• Manufacturer: Maxim Integrated Products
• Type: Step-Down (Buck)r

Specifications of MAX15035ETL+

• Internal Switch(s): Yes
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Voltage - Output: 1.05V, 1.5V
• Current - Output: 15A
• Voltage - Input: 4.5 ~ 26 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 40-TQFN Exposed Pad
• Power - Output: 2.16W
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Frequency - Switching: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

15A Step-Down Regulator with Internal Switches
EP1
(41)
EP2
(42)
EP3
(43)
PIN
32
33
34
35
36
37
38
PGOOD
NAME
REFIN
AGND
SKIP
ILIM
V
______________________________________________________________________________________
REF
FB
LX
IN
CC
Feed b ack V ol tag e S ense C onnecti on. C onnect d i r ectl y to the p osi ti ve ter m i nal of the outp ut cap aci tor s
for outp ut vol tag es l ess than 2V as show n i n Fi g ur e 1. For fixed-output voltages greater than 2V,
connect REFIN to REF and use a resistive divider to set the output voltage (Figure 6). FB senses the
output voltage to determine the on-time for the high-side switching MOSFET.
Current-Limit Threshold Adjustment. The current-limit threshold is 0.05 times (1/20) the voltage at
ILIM. Connect ILIM to a resistive divider (from REF) to set the current-limit threshold between 20mV
and 100mV (with 0.4V to 2V at ILIM).
External Reference Input. REFIN sets the feedback regulation voltage (V
MAX15035 using a resistor-divider connected between REF and GND. The MAX15035 includes an
internal window comparator to detect REFIN voltage transitions, allowing the controller to blank
PGOOD and the fault protection.
2V Reference Voltage. Bypass to analog ground using a 1nF ceramic capacitor. The reference can
source up to 50μA for external loads.
Pulse-Skipping Control Input. This four-level input determines the mode of operation under normal
steady-state conditions and dynamic output-voltage transitions:
V
REF (2V) = Pulse-skipping mode (with forced-PWM during transitions)
Open (3.3V) = Ultrasonic mode (without forced-PWM during transitions)
GND = Pulse-skipping mode (without forced-PWM during transitions)
5V Analog Supply Voltage. Internally connected to V
to analog ground using a 1μF ceramic capacitor.
Open-Drain Power-Good Output. PGOOD is low when the output voltage is more than 200mV (typ)
below or 300mV (typ) above the target voltage (V
the soft-start circuit has terminated, PGOOD becomes high impedance if the output is in regulation.
PGOOD is blanked—forced high-impedance state—when a dynamic REFIN transition is detected.
Exposed Pad 1/Analog Ground. Internally connected to the controller’s ground plane and substrate.
Connect directly to ground.
Exposed Pad 2/Inductor Connection. Internally connected to drain of the low-side MOSFET and
source of the high-side MOSFET (Figure 2). Connect LX to the switched side of the inductor as
shown in Figure 1.
Exposed Pad 3/Power MOSFET Input Power Source. Internally connected to drain of the high-side
MOSFET (Figure 2).
DD
(5V) = Forced-PWM operation
FUNCTION
REFIN
Pin Description (continued)
DD
), during soft-start, and soft-shutdown. After
through an internal 20Ω resistor. Bypass V
FB
= V
REFIN
) of the
CC
11